English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifiche Cancella tutti How do I print this? (Printing help) | RSS Pagina 180 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Nozzle getting dirty and plastic falling Da gary.b on Aug 09, 18 6547 8 alejo.v2 Under extrusion with .6mm nozzle? Da supernate91 on Aug 09, 18 3816 8 supernate91 First few layers distorted ONLY on non-PLA mat... Da Alex@AgroMe on Aug 07, 18 1539 1 Alex@AgroMe Oozing at one end causes a blob and pulls my p... Da RufusClupea on Aug 06, 18 2084 4 Sam Unexpected UNLOAD FILAMENT Da Santa Fe Bruce on Aug 06, 18 1859 3 Santa Fe Bruc... Printing Prusa PETG so confused Da Tiago on Aug 05, 18 2843 6 Plugs Perimiter defects Da Magnus on Aug 04, 18 2131 5 Magnus Problems with original Prusa silver PLA Da Protoncek on Aug 04, 18 7618 27 Protoncek Questions about a large print Da thrawn86 on Aug 03, 18 1644 2 JuanBerasain Help with supports Da Knickohr on Aug 03, 18 2117 4 Phil Screw holes printing too large Da thrawn86 on Aug 02, 18 2184 2 Chuckaluphagu... Ongoing Underextrusion and Extruder Stops Da Tim3D20 on Aug 01, 18 2827 9 Tim3D20 Updated to latest firmware and this started Da JoanTabb on Aug 01, 18 2112 2 Peter Shell Printing lower temps - nozzle temp drops too m... Da RetireeJay on Aug 01, 18 1751 2 talz13 sloped first layer not sticking to supports (f... Da jon.h5 on Aug 01, 18 1928 3 jon.h5 Problem with STL and Slic3r PE Da JoanTabb on Jul 31, 18 1430 2 JuanBerasain Problem with STL file Da bobstro on Jul 31, 18 1678 4 israel.n Print Neogeo Arcade cabinet (bigger one) Da Martin Wolfe on Jul 30, 18 1973 3 bidibule Hatchbox ABS Printing Issue Da Martin Wolfe on Jul 30, 18 3913 3 Mike77 G-Code to pause a print so I could insert hard... Da toaf on Jul 30, 18 4930 5 ckrusen Pagina 180 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Condividi: