English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Benachrichtigungen Alles löschen How do I print this? (Printing help) | RSS Seite 152 / 190 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author how to achive perfect first layer underneath f... Von -- on Jun 11, 19 5691 6 andres.m4 How to setup a PrusaSlicer 2.0 material select... Von Skypilot65 on Jun 11, 19 2218 3 Skypilot65 everything prints good except first layer Von Dschiri1 on Jun 10, 19 8000 19 Dschiri1 Wierd first layer shift Answered Von Macbeth on Jun 10, 19 2244 8 Macbeth First layer issue Answered Von -- on Jun 08, 19 2556 11 Archetrico Problem: Printing a wind turbine with PETG fai... Von -- on Jun 08, 19 3451 10 Speedriff Top Layer not so great Von MasterHead on Jun 07, 19 2095 6 MasterHead Bubbles in my print with Prusa MK3S, not happe... Von -- on Jun 06, 19 2366 4 Mike Failure at same height on multiple prints Von -- on Jun 06, 19 2181 2 KenB Sorry if wrong place to post. First time, can ... Von RetireeJay on Jun 06, 19 3051 13 HeneryH Problems printing PETG Von JBinFL on Jun 04, 19 1726 3 RichHomieTee What causes this? Too hot? Von -- on Jun 04, 19 2653 19 tellyname Drogon and Supports Answered Von MasterHead on Jun 04, 19 1968 4 MasterHead Best way to clean very fine hairs/strings on P... Von laurel.w on Jun 03, 19 20631 16 laurel.w Printing issues Von -- on Jun 03, 19 1993 6 Daredevil Prusa Slicer - Temperature rise post processin... Von -- on Jun 03, 19 2558 2 Mike Polyalchemy Elixir How all filament should be ... Von Chocki on Jun 02, 19 5785 6 Mustrum Ridcu... Slicer/printer didn't make holes Von tellyname on Jun 01, 19 4506 7 tellyname Drooping layers Von -- on May 31, 19 2366 4 Joey Changing filament material Von mpeill on May 30, 19 1367 1 mpeill Seite 152 / 190 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Nächstes Teilen: