PrusaSlicer 2.0.0 - FINAL  

RE: PrusaSlicer 2.0.0 - FINAL

Is Max layer height (printer settings/extruder 1) ignored?

I was looking through some settings to help a friend trouble shoot some issues she is having on her printers and noticed the max layer height setting for the default 0.4mm nozzle MK3S is 0.25mm, yet when I select a 0.3mm layer height print setting PrusaSlicer doesn't complain and in the preview the layers are 0.3mm. Why is PrusaSlicer allowing a 0.05mm excess in layer height of the maximum setting?

RE: PrusaSlicer 2.0.0 - FINAL

Some of those settings are most useful in setting dependencies in your print profiles.

RE: PrusaSlicer 2.0.0 - FINAL

Posted by: Sembazuru

Is Max layer height (printer settings/extruder 1) ignored?

I was looking through some settings to help a friend trouble shoot some issues she is having on her printers and noticed the max layer height setting for the default 0.4mm nozzle MK3S is 0.25mm, yet when I select a 0.3mm layer height print setting PrusaSlicer doesn't complain and in the preview the layers are 0.3mm. Why is PrusaSlicer allowing a 0.05mm excess in layer height of the maximum setting?

This setting only affects variable layer heights. 

RE: PrusaSlicer 2.0.0 - FINAL

Posted by: richard.l

Posted by: Sembazuru

Is Max layer height (printer settings/extruder 1) ignored?

I was looking through some settings to help a friend trouble shoot some issues she is having on her printers and noticed the max layer height setting for the default 0.4mm nozzle MK3S is 0.25mm, yet when I select a 0.3mm layer height print setting PrusaSlicer doesn't complain and in the preview the layers are 0.3mm. Why is PrusaSlicer allowing a 0.05mm excess in layer height of the maximum setting?

This setting only affects variable layer heights. 

Silly me, if I had bothered to read the hover text for those two text entries I would have seen that.

Thanx

RE: PrusaSlicer 2.0.0 - FINAL

I did a chat support session and cleaned up all the old files, downloaded & installed CCleaner and let it muck with my registry, re-redownload PrusaSlicer, re-re-re-reinstalled and it still fails immediately on startup.

Has anyone gotten PrusaSlicer2.0 to run on a Windows 8 machine?

RE: PrusaSlicer 2.0.0 - FINAL

Posted by: Sembazuru

Posted by: richard.l

Posted by: Sembazuru

Is Max layer height (printer settings/extruder 1) ignored?

I was looking through some settings to help a friend trouble shoot some issues she is having on her printers and noticed the max layer height setting for the default 0.4mm nozzle MK3S is 0.25mm, yet when I select a 0.3mm layer height print setting PrusaSlicer doesn't complain and in the preview the layers are 0.3mm. Why is PrusaSlicer allowing a 0.05mm excess in layer height of the maximum setting?

This setting only affects variable layer heights. 

Silly me, if I had bothered to read the hover text for those two text entries I would have seen that.

Thanx

And the range must be limited to a small factor over nozzle diameter or you'll get an error when slicing (better than the crash that use to happen).

RE: PrusaSlicer 2.0.0 - FINAL

Check your graphic card settings.

I had this problem with an old laptop, and I had to change the setting to use performance mode for PrusaSlicer.

Regards

Michael

RE: PrusaSlicer 2.0.0 - FINAL

Soooo nice to finally have 3DConnexion Space Mouse support! Been waiting for months for this update to become Final status!