Overture PLA Professional settings? - General discussion, announcements and releases

RE: Overture PLA Professional settings?

HandyObviousTank — Mon, 02 Dec 2024 15:11:57 +0000

Just did my first print w/ Overture Pla Pro and it was not sticking at all on the PET side of my magnetic build plate, might as well have been teflon. Flipped it to the PEI side and it adhered fine.

RE: Overture PLA Professional settings?

Amir S. — Mon, 30 Sep 2024 18:17:58 +0000

I'm having similar issues with bed adhesion with the PLA Professional vs. the older PLA Matte and PLA ECO, all from Overture.

Did anyone figure out good settings? It's disappointing that they don't just provide filament profiles for each of their material types.

RE: Overture PLA Professional settings?

Tincantantan — Thu, 06 Jun 2024 14:55:06 +0000

What should my infill speeds be with the regular pla

RE: Overture PLA Professional settings?

Stacy Boles — Sun, 07 Apr 2024 07:36:37 +0000

Yes, I am also have a huge problem with the regular Overture PLA and PLA professional (will not stick to the bed at all!) , but at the same time I am have perfect prints with the Overture Matte and Overture Cream.

RE:

Huntinherrington — Tue, 13 Sep 2022 08:41:09 +0000

I use prusa pla settings in prusa slicer.

Printed a 47 hr print on my very first print after printing a couple of the prints with Prusament that come on the sd card. Swapped to the Overture PLA+ and started printing.

I bought the printer assembled and did not adjust anything,

It prints great. No issues.

Nozzle 215

Bed 60

Every speed settings I have selected have been good

RE: Overture PLA Professional settings?

Tito — Thu, 01 Sep 2022 18:44:43 +0000

I am having a lot of trouble with it.

RE: Overture PLA Professional settings?

dclaar — Mon, 21 Mar 2022 04:03:04 +0000

Thanks, it works great with the Prusa PLA settings (which don't seem to be that different from others, e.g. Amazon Basics or generic).

RE: Overture PLA Professional settings?

FoxRun3D — Sun, 20 Mar 2022 12:27:56 +0000

Given their recommended range, you're probably good with the generic PLA profile. I'd run a hollowed out calibration cube to calibrate the extrusion multiplier. See https://projects.ttlexceeded.com/3dprinting_prusaslicer_extrusion_multiplier.html#wall-thickness-in-prusaslicer (I usually do a two perimeter wall)

RE: Overture PLA Professional settings?

jsw — Sun, 20 Mar 2022 01:00:15 +0000

I have not used the 'Pro' version, but most of the parameters seem like right in the ballpark for generic PLA.

The generic PLA infill speed is 80, and you might bump that down to 70 to be strictly within specs.

You can also try one of those 'temperature tower' prints to get an idea what nozzle temperature works best with that particular filament.

Overture PLA Professional settings?

dclaar — Sun, 20 Mar 2022 00:02:14 +0000

Has anyone used Overture PLA Professional? Is there a good preset?

If not, they recommend:

Recommended Extrusion/Nozzle Temp: 190 °C - 220°C (374℉~ 428℉ ),
Heated Bed Temp: 40°C - 60 °C (104℉~ 140℉)
Printing Speed:40~70 mm/s

On the "Filament Settings" tab, I can set nozzle & bed temps, and apparently use a different value for the first layer.

On the "Print Settings" tab, under Speed, there's an overwhelming number of speeds, from 25mm/sec to 200 mm/sec.

What's the best way forward?