English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 95 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Layershifts in direction of travel Da -- on Oct 25, 20 2040 7 GrepZen New to 3d printing Da PCB on Oct 24, 20 1396 3 PCB MK3S kit and first print failures. Da cwbullet on Oct 24, 20 7060 24 zaerog Print failing after several hours with warping... Da JoanTabb on Oct 24, 20 2698 8 Ryan D Seemingly Random Loose Wire in Power Supply? Da KeyPuncher on Oct 23, 20 2700 4 KeyPuncher Rough surface on sidewalls after some prints. Da -- on Oct 23, 20 2015 10 Ceasar xyz calibration failed, check owners manual Da gypsy.king on Oct 21, 20 1549 1 gypsy.king Circular Prints Failing Da karl-herbert on Oct 20, 20 1741 3 Baron Opal Bed Adhesion Issues Da jsw on Oct 19, 20 11820 27 Dustin Bearing installation Da jluvs2ride on Oct 19, 20 3687 17 jluvs2ride Persistent thermal runaway Da jurassic73 on Oct 19, 20 5167 19 Lingomat Issues when printing first layer of 0.3mm or m... Da JE Suza on Oct 19, 20 5304 9 JE Suza Very sloppy first prints Answered Da -- on Oct 18, 20 2221 8 Hotblack43 First prints, sizes problems Da -- on Oct 18, 20 1778 6 lekonna 3D Benchy Issue: Horizontal lines evenly space... Da -- on Oct 17, 20 16659 11 DespairFlare Problem of my first sword print Da -- on Oct 17, 20 4415 4 AC My printed lines are slightly wavy Da -- on Oct 16, 20 4370 5 Amlughelke "Finished" and I'm terrified I failed on fan s... Da jwvaughn on Oct 16, 20 1903 4 citizen458931 Extrusion stops after ~2-5cm printing Da -- on Oct 16, 20 1709 4 nssalee During printing strange sound when printing in... Da Area51 on Oct 15, 20 2410 6 Erwin Pagina 95 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Condividi: