English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 92 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Topic Title Last Post Views Posts Author Greasing the bearings By karl-herbert on Nov 17, 20 3756 5 Lvet Print issues - temperatures? By Nate on Nov 17, 20 1943 7 Nate Issues with "Silk PLA" By manicminergb on Nov 16, 20 24311 12 Daredevil Right side of print always off Answered By -- on Nov 15, 20 2665 16 wilkinsaf First Layer Woes - 2.00 and still no "smush" By Phish on Nov 15, 20 3972 18 Phish Marking the assembly manual for disabled folk By -- on Nov 14, 20 1760 3 ibak Acceptable stringing? By -- on Nov 14, 20 2382 3 mmacro Inconsistent Layers By -- on Nov 13, 20 1688 4 JohnP Issues new build mk3s KIT first layer and shif... By Exterminator on Nov 12, 20 1826 6 Exterminator Bed not level after bed level correct By Maker69 on Nov 12, 20 8662 19 Thai Bui First Print Misaligned after Calibration By Neophyl on Nov 11, 20 1658 4 solviento First layer calibration question Answered By BlackcQ on Nov 11, 20 1490 3 BlackcQ Multiple start up issues, sticking and failed ... By floh on Nov 11, 20 1648 4 almuzian X-axis belt tilting/deflecting By tg73 on Nov 10, 20 3422 4 harrison.y First layer problem with loose "strings" Answered By floh on Nov 10, 20 16462 21 floh Multiple issues Lines, holes and drips! By -- on Nov 10, 20 1721 2 Infiltrator New build i3 MK3 By brown.john73 on Nov 10, 20 1999 12 brown.john73 Power cable type -- not US/NA By locktec on Nov 09, 20 1652 3 jepler Z chaning after each print By -- on Nov 09, 20 2750 17 Colibri Synth... Alignment and table adherence By -- on Nov 08, 20 3468 15 Gus Favoreto Page 92 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Share: