English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 84 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author been using it for a week. and since leaving to... Przez sheriff on Jan 18, 21 1620 4 sheriff After a few Days of fine printing 1st Layer ad... Przez CarstenMT on Jan 18, 21 2006 6 CarstenMT PINDA adjustment Przez karl-herbert on Jan 17, 21 1454 3 Jerry S Prusa Mk3s - print bed has rotational "wobble" Przez Tim G on Jan 17, 21 1519 2 Tim G Unable to duplicate print Przez PS on Jan 17, 21 2010 10 PS Issues with first layer Przez JoanTabb on Jan 16, 21 1874 9 Cocomon MK3S+ second layer issue Przez PS on Jan 15, 21 2349 4 PS xyz cube calibration Przez cwbullet on Jan 15, 21 2139 2 Maassie88 Replacement of hotend Przez JoanTabb on Jan 15, 21 2599 2 eng.shaimaa.e... what allen key to use at heater assembly ? sus... Answered Przez Jason on Jan 15, 21 2833 6 Jason Mk3s+ has diferent airflow? Not permit use sam... Przez Marito on Jan 14, 21 1675 2 Marito MK2 -> MK3S+ Which parts to use? Przez Cynan on Jan 13, 21 1613 3 Robert Issue with first layer gaps and bumpy / rough ... Przez krom on Jan 13, 21 3007 2 krom !!! Screw too long - I scratched my printer !!... Przez RH_Dreambox on Jan 13, 21 1383 4 disti Initial lubrication? Przez Scott Bierly on Jan 13, 21 10833 16 cjameshuff Smooth Steel Sheet - Damage? Answered Przez Hazar on Jan 12, 21 2956 2 Hazar Issue printing Prusa demo Przez guimou on Jan 12, 21 1530 3 guimou First to Second Layer adhesion Problems Przez Diem on Jan 10, 21 1470 3 CarstenMT Just replaced PINDA and now prints look bad Answered Przez zcschu01 on Jan 10, 21 1419 7 zcschu01 Bulky messy outside Przez JoanTabb on Jan 09, 21 1213 3 LilHairdy Strona 84 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: