English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 71 / 218 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Następny Tytuł Tematu Ostatni Post Widok Posty Author I have the MK3S with MMU2S. I bought the MK3S+... Przez ssill2 on May 15, 21 2609 6 Mk4User First Layer Calibration Problem Przez ssill2 on May 15, 21 3233 17 rose359 Frame Alignment Przez JohnM on May 13, 21 4635 12 andrew.w53 Issues with PETG initially, now with PLA as we... Przez cwbullet on May 13, 21 3623 12 vanayad First print textured sheet print peeling Przez Nick on May 13, 21 3403 13 Nick Extruder Motor running Hot Przez -- on May 11, 21 2674 8 Sink printing a cylinder Przez cwbullet on May 11, 21 3194 6 justbql Newly assembled Prusa and prints quality Przez cwbullet on May 10, 21 2808 5 k3213 Leaky nozzle - how much to disassemble? Przez -- on May 10, 21 2740 8 Paul New to 3D printing and Prusa Products. Is this... Przez Taxane on May 10, 21 4343 7 Taxane Assembly completed and first print Przez Andrew Weitzel on May 09, 21 2576 5 Andrew Weitze... Gap Fills Issue Przez Rocky79 on May 09, 21 4875 18 Rocky79 y axis bearing noise at initial assembly Przez cwbullet on May 08, 21 4380 8 john XYZ Calibration Issue Przez -- on May 08, 21 2142 8 MinorMatt MK3S+ printing fan not working - cannot comple... Przez Clarmrrsn on May 08, 21 2856 3 admpc scale units mm/inches Przez -- on May 07, 21 5176 7 Jerry S Fan not spinning Przez 3Delight on May 07, 21 5846 16 boulland.mich... Nozzle hits prints off after about 450mm Answered Przez cwbullet on May 07, 21 22593 46 Milazzone First print quality feedback Przez cwbullet on May 07, 21 2504 3 quody Test pattern is not sticking to heatbed Przez cwbullet on May 07, 21 6116 27 CJSHayward Strona 71 / 218 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Następny Share: