English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Stránka 71 / 218 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author Frame Alignment Od JohnM on May 13, 21 4574 12 andrew.w53 Issues with PETG initially, now with PLA as we... Od cwbullet on May 13, 21 3537 12 vanayad First print textured sheet print peeling Od Nick on May 13, 21 3339 13 Nick Extruder Motor running Hot Od -- on May 11, 21 2634 8 Sink printing a cylinder Od cwbullet on May 11, 21 3117 6 justbql Newly assembled Prusa and prints quality Od cwbullet on May 10, 21 2779 5 k3213 Leaky nozzle - how much to disassemble? Od -- on May 10, 21 2717 8 Paul New to 3D printing and Prusa Products. Is this... Od Taxane on May 10, 21 4251 7 Taxane Assembly completed and first print Od Andrew Weitzel on May 09, 21 2544 5 Andrew Weitze... Gap Fills Issue Od Rocky79 on May 09, 21 4774 18 Rocky79 y axis bearing noise at initial assembly Od cwbullet on May 08, 21 4324 8 john XYZ Calibration Issue Od -- on May 08, 21 2100 8 MinorMatt MK3S+ printing fan not working - cannot comple... Od Clarmrrsn on May 08, 21 2824 3 admpc scale units mm/inches Od -- on May 07, 21 5093 7 Jerry S Fan not spinning Od 3Delight on May 07, 21 5740 16 boulland.mich... Nozzle hits prints off after about 450mm Answered Od cwbullet on May 07, 21 22116 46 Milazzone First print quality feedback Od cwbullet on May 07, 21 2478 3 quody Test pattern is not sticking to heatbed Od cwbullet on May 07, 21 5930 27 CJSHayward Can't get first layer right Answered Od Veritas on May 07, 21 2610 5 Veritas Y-axis assembly issues / frame skew Od -- on May 07, 21 3303 6 hullcb Stránka 71 / 218 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Další Share: