English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 60 / 216 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Z Axis crash Por John Doe on Aug 10, 21 2225 3 John Doe Another z issue? Prints pull off sheet after 5... Por Doug Glenn on Aug 09, 21 1617 4 sjmotew benchy silk pla issues Por morbo on Aug 09, 21 2823 5 morbo Fan-shroud broke during assembly Por cwbullet on Aug 09, 21 1181 5 JGM Fully assembled i3 MKS+ issues Por dudendy on Aug 08, 21 1474 5 dudendy Can't get frame square on first assembly Por JoanTabb on Aug 07, 21 1237 3 Bryan34 Filament won't load Por Gray on Aug 07, 21 1394 8 Gray Just prints a few layers Por Runaljod on Aug 07, 21 1682 9 Runaljod Help before I send this thing back. Por karl-herbert on Aug 06, 21 4138 39 Burrfree Can I upgrade to the belt tensioner on my mk3? Por cwbullet on Aug 06, 21 1056 2 Miriam Was z-level calibration done correctly? Por FlyingCog on Aug 05, 21 1721 5 FlyingCog Blobs issue Por Rocky79 on Aug 04, 21 2024 12 Rocky79 Under/overextrusion, temperature? Por ktm1090 on Aug 04, 21 2290 10 ktm1090 Uneven Print Por cwbullet on Aug 04, 21 1788 11 Jacob How do I fix these uneven walls? Por Mark Blasco on Aug 04, 21 4577 12 Mark Blasco Filament sticking to the nozzle Por bobstro on Aug 03, 21 6631 10 Q Odd Shift at the top of the print Por mgtarallo on Aug 02, 21 1057 7 mgtarallo Some questions about getting the first few lay... Por Dan Rogers on Aug 02, 21 1446 2 Awong1214 Bad solid-infill but good top-solid-infill? Por muzz on Aug 01, 21 1584 3 muzz Strange Vertical Lines on Flat Surfaces Answered Por Tarek Sobh on Jul 31, 21 2073 4 Tarek Sobh Página 60 / 216 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Siguiente Compartir: