English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 54 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Topic Title Last Post Views Posts Author Solid Infill Sagging By EricRidesDirt on Nov 13, 21 2147 3 EricRidesDirt New build initialisation won't get past settin... Answered By alidaf on Nov 12, 21 1444 5 alidaf Small Space at the Bottom of the Print Answered By bunjeeb on Nov 12, 21 1897 8 bunjeeb Heatbed Target Temperature drops to Zero after... Answered By Neophyl on Nov 12, 21 1780 6 Detlev Assembling an i3 MK3S+ in 8 minutes By roc856 on Nov 10, 21 1968 1 roc856 Spare part print issue? Answered By BogdanH on Nov 10, 21 1380 9 Odin sensor filamento By Dan Rogers on Nov 10, 21 1438 2 JOSE GARCIA PETG won't adhere to double side textured PEI ... By JSA on Nov 08, 21 2780 6 Phil FX Chasing adhesion issues and question about z c... By Mic on Nov 08, 21 1373 5 Mic Hotend Heating Testing Protocol question: New ... Answered By JoanTabb on Nov 08, 21 1225 5 Ozimandius Another noob with wizard 'Calibration failed!,... By cwbullet on Nov 08, 21 1747 5 SSN613 problem with 1st layer on a large squared surf... Answered By fco on Nov 07, 21 2051 9 fco x axis shift By Diem on Nov 07, 21 1168 3 Dahlia503 What would cause these horizontal lines? By BogdanH on Nov 07, 21 2215 2 SwimClips Stringing issues with prusament By zzjlamb on Nov 06, 21 5643 8 StrangelyType... Error: axis length X Answered By R. Jonas on Nov 05, 21 1322 3 R. Jonas Long tail and zigzag By Neophyl on Nov 04, 21 1545 5 enkumi Bed Level Correction Test- Center & Center Lef... By Dan Rogers on Nov 04, 21 1644 6 Knarfly Ninjatek Cheetah Settings for PrusaSlicer By Dangc10 on Nov 03, 21 6329 3 davisjc22 Self-Destructing Printer By HakunaMatata on Nov 03, 21 2042 12 Touchstone Page 54 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Share: