English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 30 / 216 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author underextrusion? Von boinappi on Sep 26, 22 1250 6 Ladrogue New printer error in initial setup: "Calibrati... Von schrodinbug on Sep 25, 22 2403 6 DF "some problem encountered z leveling enforced" Von JulieL on Sep 25, 22 1921 6 JL Flattened corners after slicer upgrade Von mgtarallo on Sep 22, 22 1746 15 mgtarallo Preheating nozzle Please wait message Von Syno on Sep 21, 22 2187 6 Saz First prints following upgrade from MK3S to MK... Von cwbullet on Sep 21, 22 1200 4 Tekin Ozbek Prusa i3 MK3S+ after final assambly not turn o... Von karl-herbert on Sep 16, 22 1329 4 PrusaPrinters... Filament sensor wiring error Von JoanTabb on Sep 16, 22 4075 10 thomas.a21 Filament sensor wiring error MK3 Von cwbullet on Sep 16, 22 2392 2 Petver62 Can't get anything to stick Answered Von P.O. on Sep 15, 22 1509 9 oobedoob Problème d'impression première couche PETG Von Jacques Rigal on Sep 15, 22 2131 4 Jacques Rigal Help just finished building printer Von Netpackrat on Sep 14, 22 1499 5 Christopher P... A quick sigh of relief and thanks Von RandyM9 on Sep 11, 22 1468 3 Baz First Prints Von Neophyl on Sep 11, 22 1204 11 daveetch rough sidewalls Von SFilipp on Sep 10, 22 1267 3 SFilipp New printer, X axis out of alignment on first ... Answered Von Greysoul on Sep 08, 22 946 5 Greysoul Help requested: First Layer Calibration: "some... Answered Von Joe on Sep 07, 22 1329 2 Joe Cant get past Calibrate XYZ without paper movi... Von Diem on Sep 06, 22 1278 3 3dPrinterGoBo... Distorted Benchy with banding 🙁 (first print) Von ormstont on Sep 06, 22 2141 9 ormstont Inclined nozzle - cause of problem? how to fix... Answered Von Pfriemler on Sep 05, 22 2385 10 Pfriemler Seite 30 / 216 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Nächstes Teilen: