English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 207 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Y Axis (Front Idler tracking) Por ewr2san on Jun 14, 18 2861 8 ewr2san Layer Shift Issues Por JoanTabb on Jun 13, 18 1507 2 cristian.a2 Dead in the water Por Joe Prints on Jun 13, 18 1632 2 master moccas... Filament getting stuck upon removal Por Gato on Jun 13, 18 3217 6 BootStrap Top Layer help Por ritchrock on Jun 12, 18 2204 8 ritchrock XYZ Calibration Issue Por henry.b2 on Jun 12, 18 2167 5 Aaron Coté First print great, since then - all crash (x-a... Por JoanTabb on Jun 12, 18 2280 7 matt.l19 Shifting layers randomly and stringing Por Gato on Jun 11, 18 2596 5 aowilkie Bed Leveling Failed Por Gibby on Jun 11, 18 2231 6 Gibby Strands of filament all over left half of laye... Por Bruce B on Jun 11, 18 2426 5 Bruce B First power up, no config screen Por gregory.t5 on Jun 10, 18 1347 3 gregory.t5 Calibrating Z won't go up! Por robert.l31 on Jun 10, 18 5719 10 jeanloup.l Devastated - Jaw doppingly poor print quality Por Sean on Jun 10, 18 2766 11 Sink Wrong Home Position Por Skywalker86 on Jun 10, 18 8478 4 Skywalker86 Checking Z-axis: nozzle hits bed with whatever... Por nenad.b on Jun 09, 18 3741 3 christophe.l8 XYZ Calibration fails - PINDA probe off of cal... Por Marc_G on Jun 09, 18 2200 4 Marc_G Broken hotend wire, 6 hours of PLA piled up on... Por Cliff Miller on Jun 08, 18 5216 8 Cliff Miller XYZ cube problems - hard lines above and below... Por talz13 on Jun 08, 18 2656 2 talz13 Y Axis length error (motor doesn't know when i... Por Olef on Jun 08, 18 1798 2 Alex Donaghue Axis limit error Y Por GeneMpls on Jun 07, 18 1872 2 GeneMpls Página 207 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: