English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 207 / 217 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Filament stuck to the metal sheet Von Fotoman on Jun 14, 18 4564 6 Ryan Larson Y Axis (Front Idler tracking) Von ewr2san on Jun 14, 18 2861 8 ewr2san Layer Shift Issues Von JoanTabb on Jun 13, 18 1507 2 cristian.a2 Dead in the water Von Joe Prints on Jun 13, 18 1632 2 master moccas... Filament getting stuck upon removal Von Gato on Jun 13, 18 3221 6 BootStrap Top Layer help Von ritchrock on Jun 12, 18 2205 8 ritchrock XYZ Calibration Issue Von henry.b2 on Jun 12, 18 2168 5 Aaron Coté First print great, since then - all crash (x-a... Von JoanTabb on Jun 12, 18 2280 7 matt.l19 Shifting layers randomly and stringing Von Gato on Jun 11, 18 2596 5 aowilkie Bed Leveling Failed Von Gibby on Jun 11, 18 2231 6 Gibby Strands of filament all over left half of laye... Von Bruce B on Jun 11, 18 2427 5 Bruce B First power up, no config screen Von gregory.t5 on Jun 10, 18 1347 3 gregory.t5 Calibrating Z won't go up! Von robert.l31 on Jun 10, 18 5721 10 jeanloup.l Devastated - Jaw doppingly poor print quality Von Sean on Jun 10, 18 2767 11 Sink Wrong Home Position Von Skywalker86 on Jun 10, 18 8479 4 Skywalker86 Checking Z-axis: nozzle hits bed with whatever... Von nenad.b on Jun 09, 18 3742 3 christophe.l8 XYZ Calibration fails - PINDA probe off of cal... Von Marc_G on Jun 09, 18 2202 4 Marc_G Broken hotend wire, 6 hours of PLA piled up on... Von Cliff Miller on Jun 08, 18 5217 8 Cliff Miller XYZ cube problems - hard lines above and below... Von talz13 on Jun 08, 18 2656 2 talz13 Y Axis length error (motor doesn't know when i... Von Olef on Jun 08, 18 1799 2 Alex Donaghue Seite 207 / 217 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Nächstes Teilen: