English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 179 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Topic Title Last Post Views Posts Author First layer streaks? By -- on Jan 18, 19 3649 8 P. Larsen Gaps in on left side By terence.t2 on Jan 18, 19 1307 3 terence.t2 Dear Mr Prusa, By cwbullet on Jan 18, 19 1970 6 karl.w4 What do I call this? By stephen.h14 on Jan 17, 19 1903 4 stephen.h14 MK3 Benchy results - recommendations to improv... By magiclantern on Jan 17, 19 2137 7 magiclantern Degraded prints over time By IaMaCuP on Jan 17, 19 1621 3 IaMaCuP Z level not consistent across plate By Chocki on Jan 17, 19 2465 8 P. Larsen So I added lithium grease to my smooth rods wi... By bill de_cat on Jan 16, 19 849 4 bill de_cat Problem with over tight trapezoidal nut and X-... By Bizilux on Jan 16, 19 4537 5 Bizilux Ripping first layer? By MikiCab on Jan 16, 19 1793 2 Alpha Help analyze first layer issues By Chocki on Jan 15, 19 1300 2 barak.o Help to analyse the first benchy By Patrick McNama... on Jan 15, 19 2757 7 davide.s6 First layer print issues By RH_Dreambox on Jan 15, 19 1488 2 florin.a X Axis Assembly By Sukkubix on Jan 15, 19 2625 7 Sukkubix Calibration failed error By conc on Jan 15, 19 2331 11 conc Underextrusion By magiclantern on Jan 15, 19 2458 9 MileHigh3Der Retraction problems By Chocki on Jan 14, 19 3439 2 geert.g2 Power-on stuck at language choice By Calire on Jan 14, 19 2170 2 GGFuzzy Knob problems By JoanTabb on Jan 14, 19 1684 5 Max C. Print goes haywire at similar point each time By anthony.m26 on Jan 12, 19 2850 13 anthony.m26 Page 179 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Share: