English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 178 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Topic Title Last Post Views Posts Author First Layer Height setting? By Nikolai on Jan 22, 19 4216 4 Snardo Strange noise on change of direction diagonall... By Steve on Jan 21, 19 3541 4 Steve Yellow PETG adhesion/density issues around lay... By thomas.h59 on Jan 21, 19 2641 11 thomas.h59 PLA Bed Adhesion issues, Help! By -- on Jan 21, 19 2525 4 Snardo Odd issue with higher layers on newly built ki... By Bret on Jan 21, 19 1248 3 Bret Weird characters displayed during bed calibrat... By Frank on Jan 21, 19 2061 4 Frank Some prints work, some don't By Shelby Teknolo... on Jan 21, 19 1463 3 Shelby Teknol... Repair advice PRUSA I3 MK3 MULTI MATERIAL 2.0 By Vegas Pay LLC on Jan 20, 19 1483 1 Vegas Pay LLC X axis binding and bottom 2 screws on X carria... By jon bondy on Jan 20, 19 1585 3 jon bondy Strings more visible over time By Felix on Jan 20, 19 1751 4 Felix XYZ Axis Calibration Error By RH_Dreambox on Jan 20, 19 1272 2 Fuganater Zaxis problems By RH_Dreambox on Jan 20, 19 1692 3 Max C. XYZ Axis Calibration Error at first point By Joe on Jan 20, 19 1992 3 aaron.k13 Are my walls acceptably ‘smooth’? By Nikolai on Jan 20, 19 3008 9 Adam Has anyone had an intermittent extruder issue ... By MikiCab on Jan 19, 19 2205 10 MikiCab Bad Top Layer Finish? By Bunny Science on Jan 19, 19 2051 3 D.Pierce What does the Smooth Sheet PEI build plate loo... By JoanTabb on Jan 19, 19 1472 2 Snardo First layer fine... 2nd and 3rd not so much By JoanTabb on Jan 19, 19 1274 3 martin.c28 Bed not level By GeorgeE on Jan 19, 19 1980 5 OmegaPax First layer streaks? By -- on Jan 18, 19 3640 8 P. Larsen Page 178 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Share: