English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 157 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author XYZ Calibration constantly failing Przez -- on Jun 02, 19 1783 7 Overkill Settings for filaments Przez Peter M on Jun 01, 19 2359 3 Schehlein Calibration Test Failure Przez torinp.busines... on Jun 01, 19 3035 13 torinp.busine... Can't unload filament Przez mpeill on Jun 01, 19 1312 2 mpeill some thoughts and a problem Przez xt550 on Jun 01, 19 2503 11 xt550 Trouble with PET after update to FW 3.7.1 and ... Answered Przez Chocki on May 31, 19 2098 4 John First print: is this sound normal? Plus Y belt... Przez -- on May 30, 19 1837 3 Cedar Looking for first timer test print feedback Przez -- on May 30, 19 1634 6 christopheran... Blobs and zits Przez -- on May 30, 19 1988 2 nike.56 Disabled filament sensor to print Answered Przez Willo47 on May 30, 19 9036 19 Michael23 Can't print triceratops Przez bobstro on May 29, 19 3230 13 lorin.kobashi... Motor pulley too loose Y Przez -- on May 29, 19 5343 2 Dimensions of... Filament won't load Answered Przez n3rd on May 29, 19 2221 6 n3rd Layer adhesion and cooling Przez bobstro on May 28, 19 2534 2 ronald.g4 Thermal Runaway MK3s - Part cooling fan blowin... Przez Milos V. on May 27, 19 1456 2 MrTarantl Initial setup calibration problem print fan Answered Przez holblin on May 27, 19 1276 3 holblin First few print problem Przez Mickfb on May 26, 19 1373 3 Mickfb Shifts in first prints off newly built kit Answered Przez -- on May 26, 19 1987 5 dgbonomo Print problems Przez Bogas on May 26, 19 1304 2 Bogas Heater /Thermistor Not Connected Przez doot doot beep on May 26, 19 2789 1 doot doot bee... Strona 157 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: