English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Stránka 150 / 217 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author What went wrong? Od mmihi on Jul 31, 19 1895 6 mmihi Mk3S IR Filament Sensor Od bernardjbisel on Jul 31, 19 3947 15 John~T Calibrate XYZ Fail i3 MK3 Od reesor on Jul 31, 19 2648 15 reesor Assembly guide Bondtech aligment, black nylon ... Od -- on Jul 30, 19 2876 4 Mistral33 MK3S Upgrade - Hotend loose Od Sunshadow on Jul 30, 19 2537 3 Sunshadow Extruder idler tensioner issue Od Mike01Hu on Jul 30, 19 3616 5 Mike01Hu Leftover red cable from hotend Od -- on Jul 30, 19 3619 19 prusanewuser MK3S - Hot Extruder and skipping at start time Od TigerClaw35 on Jul 30, 19 1432 1 TigerClaw35 New kit, can not calibrate. Od dispo on Jul 30, 19 2360 10 dispo Bad accuracy on x-axis Od -- on Jul 29, 19 2739 5 4Bob Octoprint stopped Od bobstro on Jul 29, 19 1388 2 luka.b3 Troubleshooting fine pillars Od lindharin on Jul 29, 19 5442 16 laurel.w Self test at hotend check does a reboot Od jkunjoonju on Jul 28, 19 2363 3 jkunjoonju Why does this happen at the same spot? Od -- on Jul 27, 19 1607 3 ametwalyhsgca Deteriorating nozzle temperature correctness l... Od bobstro on Jul 27, 19 1947 4 Cronostitan Calibration XYZ failed Od plevin on Jul 27, 19 4305 20 Laura Print problems Od luka.b3 on Jul 27, 19 1469 10 luka.b3 Weird Noise during print Od Elad6k on Jul 26, 19 3388 19 clementszwech... Filament stuck Od kronoss on Jul 26, 19 3430 9 kronoss Filament sensor Issues Od richardkwofie on Jul 25, 19 1533 4 richardkwofie Stránka 150 / 217 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Další Share: