English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 138 / 218 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Następny Tytuł Tematu Ostatni Post Widok Posty Author Check Axis Length X Przez JoanTabb on Nov 19, 19 2508 7 TechTiger where i must put this cable? many tanks who he... Przez mukkio on Nov 19, 19 1918 4 mukkio Depth of extruder screws (on left: M3x40 with ... Przez -- on Nov 19, 19 2360 4 JK Z calibration fails almost immediately Przez -- on Nov 17, 19 3187 10 tapwater First layer calibration and Z calibration Przez rmm200 on Nov 17, 19 4047 4 tapwater Adopted 2nd Prusa MK3 continuing issues... nex... Przez -- on Nov 17, 19 1931 4 jdoscher MK3 - Extruder is not heating up after replaci... Przez devang.p on Nov 16, 19 2302 4 devang.p MK3S Kit first print - Improvements Przez -- on Nov 15, 19 2333 5 danyag Offset in the print image! Przez sascha-1 on Nov 15, 19 1747 5 sascha-1 Not completing Setup Wizard Przez Graham666 on Nov 14, 19 2780 3 Graham666 No assembly manual included now? Przez Nikolai on Nov 13, 19 2541 7 iamramondredd... Printing multiple items causes crash Przez -- on Nov 13, 19 4688 12 dandmrogers Clicking, filament under extrusion. Brand new ... Przez TC on Nov 13, 19 2422 8 TC Rough surface on print Przez Scouter456 on Nov 12, 19 10537 17 Scouter456 Z calibration perpetual fail. Przez michael.p77 on Nov 12, 19 2128 13 michael.p77 Do you need a first layer calibration when cha... Przez -- on Nov 12, 19 3448 4 Mike@Ground_S... Inconsistent lines and curves Przez -- on Nov 12, 19 2332 2 mparker2531 Brand new Mk3s Printer won’t start up... Przez James on Nov 10, 19 4040 8 James new buildt, the steering knob on the display d... Przez MK on Nov 10, 19 5859 19 MK First Layer Calibration/ Bed Leveling Issues Przez MK on Nov 10, 19 4193 6 cf1it Strona 138 / 218 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Następny Share: