English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 125 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author My 2nd Mk3 has got to be defective. Nothing bu... Por MegardStudio on Mar 26, 20 1816 3 MegardStudio Self Test Fail - Y-Axis Por Jonas on Mar 26, 20 1935 2 Balki Some problem encountered, Z-leveling enforced.... Por 1ProjectAWeek on Mar 25, 20 3045 3 1ProjectAWeek First Layer problems - Inconsistency Answered Por jorge.s6 on Mar 25, 20 3576 13 danny.l5 Failed Prints - Detaching from Print Bed After... Por Bison25 on Mar 25, 20 2024 5 Bison25 Printer reboots midprint, LCD garbled Por stdio.h on Mar 25, 20 1872 4 stdio.h Textured sheet failure. Por rmm200 on Mar 25, 20 1863 4 indysam Wont read sd card Answered Por Steve on Mar 25, 20 1764 2 Spiffy Wolf Had my first failed print today. Anyone know w... Por JoanTabb on Mar 24, 20 1420 3 Max Maker Paper sheet gets stuck upon the Z axis calibra... Por Jay on Mar 24, 20 3409 6 Jay Yet another "XYZ calibration failed. Please co... Por Fitch on Mar 24, 20 2585 5 Fitch Print settings in PrusaSlicer vs in-Printer? A... Por Andrew Biss on Mar 24, 20 2135 4 Andrew Biss Excessive stringing, oozing, and whistle bridg... Por Jimmy Chapel on Mar 24, 20 3779 4 Jimmy Chapel XYZ calibration failed. Bed calibration point ... Por r-p.caron on Mar 23, 20 2940 4 r-p.caron Normal then under extrusion Por RH_Dreambox on Mar 23, 20 1996 2 Ali Jennings Part versions Por Astroprinter on Mar 22, 20 1625 1 Astroprinter X-Axis Belt Slipping During Calibration. Can't... Answered Por Dave on Mar 21, 20 3217 9 Dave Initial Calibration failure Por karl-herbert on Mar 20, 20 2824 5 jean-marc.dem... Bear Bondtech X-Axis won't calibrate. Por Elmo on Mar 20, 20 1877 1 Elmo New Printer. Won't extrude Por rmm200 on Mar 19, 20 1804 3 gigem2 Página 125 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: