English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 122 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Cannot calibrate XYZ - always fails on finding... Answered Da zabg on Apr 11, 20 2606 4 zabg New PLA brand = new first layer calibration ? Da Ben on Apr 11, 20 2558 10 Ben First Assembly Tips? Da Pedroid on Apr 11, 20 2697 3 RayRay First layer calibration - load does not stop, ... Answered Da raoul on Apr 10, 20 1837 2 raoul subsequent early layers issue Da Peter M on Apr 10, 20 1558 2 Mark Travis 1st layer troubles on large prints Da Peter M on Apr 09, 20 2005 8 MisteurJ Issue with the filament autoload and filament ... Da JustMe3D on Apr 09, 20 2814 2 cesar.perez First layer issues - getting to it, temp, shee... Da Peter M on Apr 09, 20 2588 2 flohoff Unplanned Holes in outside layer issue Da Marcin on Apr 09, 20 2282 10 Marcin Fist layer finishing and appearance - settings... Da RH_Dreambox on Apr 09, 20 2846 10 impression3D.... First layer problems Da Wokipokei on Apr 08, 20 2197 5 Wokipokei Help with first layer oddites [New Build] Da UK Teacher on Apr 08, 20 1875 3 UK Teacher Calibration issues after build (Bed calibratio... Da Jesuso on Apr 08, 20 1992 1 Jesuso Possible X axis print problem Da karl-herbert on Apr 08, 20 1528 5 nmday First Print Stuck in Loop Da karl-herbert on Apr 08, 20 1613 2 JWP_311 Extruder trouble during assembly Answered Da JoanTabb on Apr 07, 20 1407 4 Brad811 PET Crash... Da christopher.c3... on Apr 07, 20 1606 3 christopher.c... Bed Topography with Pronterface Da AndyInSwindon on Apr 07, 20 7112 8 AndyInSwindon No filament pulling, maybe missing a screw ? Answered Da cyr.paulhiac on Apr 07, 20 2967 8 cyr.paulhiac MMU2 installation testing Da JoanTabb on Apr 07, 20 1529 3 ggmeddles Pagina 122 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Condividi: