English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 110 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author Top Layers Are Shiny/Underextruding Towards Mi... Przez m00dawg on Jun 21, 20 7009 6 Graham Shotts Is this too squished ? Przez -- on Jun 20, 20 3228 4 DanielM layer lines not connecting to walls Przez Neophyl on Jun 20, 20 5269 6 ametwalyhsgca Filament do not flow during print but does goo... Przez Arek on Jun 20, 20 3334 14 thomas-4 Filament stuck / clogging Przez JoanTabb on Jun 20, 20 3713 8 Andreas XYZ calibration failure. Przez karl-herbert on Jun 19, 20 2215 10 rflournoy Mk3s Kit Built, Not Passing Self Tests and Cal... Przez cadeucsb on Jun 18, 20 2022 4 cadeucsb The printer keeps asking me to load and reload... Przez Andy on Jun 18, 20 2179 4 Andy Inconsistent first layer in some places Przez Ixian on Jun 18, 20 1919 2 mgtarallo Is there a command via LCD to load filament an... Przez HeneryH on Jun 17, 20 2577 9 HeneryH First layer and leaking issues Przez JoanTabb on Jun 17, 20 1985 2 Jake Y shift on new build? Przez sanjay on Jun 17, 20 1467 3 sanjay Trouble with first print Przez -- on Jun 17, 20 1477 2 bartek_sekows... Just a quick question Przez zephirekott on Jun 16, 20 1312 5 zephirekott Calibration Przez JoanTabb on Jun 16, 20 1619 2 Eric Extra material attached to head bed for first ... Przez Loak on Jun 15, 20 1706 6 knavelfamily X Axis issue Przez Martina Pi on Jun 15, 20 2154 6 Martina Pi first time start up - keeps asking for languag... Przez JoanTabb on Jun 15, 20 2942 4 jimc First prints - extra material / residue at sta... Przez JoanTabb on Jun 15, 20 1646 4 Stil190 New build, Y axis issues Przez Lize on Jun 14, 20 2037 5 Infra-Red Strona 110 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: