English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Messages récents Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 109 / 217 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Suivant Titre du sujet Dernier message Nombre de vues Messages Author First Print - I am sure that this is not right... Par CovertPluto350... on Jun 30, 20 1728 5 Pieter-Michie... Weird inaccuracies in first print (MK3S Kit) Par Leonard Gerhar... on Jun 29, 20 1716 4 Leonard Gerha... IR Sensor on MK3S not functioning proper Par PRINT 09 s.r.o... on Jun 29, 20 5958 13 Brankomer Rattle on fine / fast movements tracked down t... Par 3DPrintM.D. on Jun 29, 20 1901 3 3DPrintM.D. new kit, tuning my floaty boaty Par wookey on Jun 29, 20 1683 2 wookey P.I.N.D.A Adjustment and first-layer calibrati... Par Peter M on Jun 26, 20 2768 3 Fred New textured sheet and ready to toss my printe... Par cwbullet on Jun 25, 20 5173 26 Fraser the co... Mk3S Assembly Par Erny on Jun 25, 20 2132 5 joelbatista Mucky rough first layer, and flat prints detac... Par 01Pad on Jun 25, 20 6245 5 01Pad first prints issues - uneven quality throughou... Par Peter M on Jun 25, 20 2071 3 saemann.log First prints with oozing and blobs Par Neophyl on Jun 24, 20 3775 10 Danny B Linear error Par rgesikov on Jun 23, 20 1499 1 rgesikov XYZ Calibration failed - Z axis problem Answered Par chiopere on Jun 23, 20 1907 2 chiopere First prints with small holes Par -- on Jun 23, 20 4004 2 Cloud66 X-axis alignment issues Par JoanTabb on Jun 22, 20 2984 4 Foyler Second layer problem Par Walleye on Jun 22, 20 9347 17 Razaro Help understanding calibration issues Par JoanTabb on Jun 21, 20 1807 4 jimc first benchy prints with hatbox abs have stran... Par jsw on Jun 21, 20 3093 14 the-sh1z taulman nylon 230 vertical screw printing issu... Par the-sh1z on Jun 21, 20 1567 1 the-sh1z The x-axis belt is too close to the plastic (r... Par Gigios on Jun 21, 20 3289 14 Gigios Page 109 / 217 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Suivant Partager :