Notifications
Clear all

Unofficial Prusa XL Waiting Thread  

Page 37 / 39
  RSS
burtronix
(@burtronix)
Reputable Member
RE: Unofficial Prusa XL Waiting Thread

Unless you really just enjoy the tinkering, It's much easier to get one of these. However, if you DIY, you should figure out how much you need to bore out the orifice to leave the right diameter after adding the coating. You might need to do some taper-boring in the throat area to get the right flow-geometry.

https://www.amazon.com/Micro-Plated-Hardend-Nozzle-RepRap/dp/B07CGCBPLN/ref=sr_1_5?keywords=micro%2Bswiss%2Bnozzle&qid=1698414138&sr=8-5&th=1

Posted by: @jeggo

I am also thinking of DIY coating a brass nozzle. I am quite sure, that I read/see something about this. But I could not remember where or what the exact solution was. I only found a video which recommends to apply MoS2 grease/oil. This should work to temperature up to 450°C.

Any hints or suggestions? 

 

Whatever you find to do with your hands, do with all your might!

Posted : 27/10/2023 1:47 pm
Jeggo
(@jeggo)
Estimable Member
RE: Unofficial Prusa XL Waiting Thread

@burtronix: Thanks for the hint. But this leads to a loss of comfort when changing the nozzle. Either I need an adaptor for each nextruder. The Prusa ObXidian will cost about 60€ and is out of stock at the moment.

Posted : 27/10/2023 2:21 pm
burtronix
(@burtronix)
Reputable Member
RE: Unofficial Prusa XL Waiting Thread

@Jeggo,

I'm planning on getting a bunch of adaptors anyway. I want to have multiple hardened nozzles. Changing nozzles with adaptors can't be any more challenging than changing nozzles on my Mini or MK3S.

Whatever you find to do with your hands, do with all your might!

Posted : 27/10/2023 4:12 pm
toby.k
(@toby-k)
Trusted Member
RE: Unofficial Prusa XL Waiting Thread

I finally pulled the payment trigger last night on my day one XL two head order. Got an email 14 hours later with a shipping tracking number.

"Your order with the reference number 16372xxxxx has been packed and the tracking number has been generated. Your order will be expedited soon."

Posted : 01/11/2023 1:39 pm
Georg liked
dvillalba3d
(@dvillalba3d)
Trusted Member
RE: Unofficial Prusa XL Waiting Thread

Whoa! Congrats! That's quick! First day order?

 

Posted by: @toby-k

I finally pulled the payment trigger last night on my day one XL two head order. Got an email 14 hours later with a shipping tracking number.

"Your order with the reference number 16372xxxxx has been packed and the tracking number has been generated. Your order will be expedited soon."

 

Posted : 01/11/2023 1:49 pm
Georg
(@georg-4)
Estimable Member
RE:

Nice! So it looks like there are still many orders in queue. My order was placed on the 29th of Nov and the order number starts with 16381xxxxx

Posted : 01/11/2023 1:54 pm
dvillalba3d
(@dvillalba3d)
Trusted Member
RE: Unofficial Prusa XL Waiting Thread

November 20th here... 😓

Posted by: @georg-4

Nice! So it looks like they are coming to an end in shipping day one orders. My order was placed on the 29th of Nov and the order number starts with 16381xxxxx

🙂

 

Posted : 01/11/2023 1:57 pm
Georg
(@georg-4)
Estimable Member
RE: Unofficial Prusa XL Waiting Thread

What are the first 5 digits of your order number?

Posted : 01/11/2023 1:57 pm
dvillalba3d
(@dvillalba3d)
Trusted Member
RE: Unofficial Prusa XL Waiting Thread

Wait! My number is 16374! What does it mean? Are they following these numbers??

 

Posted : 01/11/2023 2:00 pm
dvillalba3d
(@dvillalba3d)
Trusted Member
RE: Unofficial Prusa XL Waiting Thread

Mine was semi assembled 2 heads, your too? Or fully assembled?

Posted by: @toby-k

I finally pulled the payment trigger last night on my day one XL two head order. Got an email 14 hours later with a shipping tracking number.

"Your order with the reference number 16372xxxxx has been packed and the tracking number has been generated. Your order will be expedited soon."

 

Posted : 01/11/2023 2:03 pm
Georg
(@georg-4)
Estimable Member
RE: Unofficial Prusa XL Waiting Thread

Mine was semi assembled 2 heads, your too? Or fully assembled?

Mine is also semi assembled.

Are they following these numbers??

I guess so. But there are also non XL orders between. So i shouldn‘t take long until yours is send as you are near the order of toby.k 🙂

Posted : 01/11/2023 2:06 pm
Area51
(@area51)
Member
RE: Unofficial Prusa XL Waiting Thread

Got an email yesterday that my XL 5h semi assembled order was picked up by DHL (Order 16372xxxxx from November 19. 1 am 2021).
Expected delivery is Monday 6.11.2023 - time to finish the MK3S+ to MK3.9 upgrade and make room for the XL build...

Have a look at my models on Printables.com 😉

Posted : 01/11/2023 2:34 pm
toby.k
(@toby-k)
Trusted Member
RE: Unofficial Prusa XL Waiting Thread

Yes, first day order.  I got my first notice that I could finalize and pay for it weeks ago, just waited since I was not sure I still wanted it.

Posted : 01/11/2023 3:33 pm
toby.k
(@toby-k)
Trusted Member
RE: Unofficial Prusa XL Waiting Thread

Mine was also semi assembled, 2 heads.

Posted by: @dvillalba3d

Mine was semi assembled 2 heads, your too? Or fully assembled?

Posted by: @toby-k

I finally pulled the payment trigger last night on my day one XL two head order. Got an email 14 hours later with a shipping tracking number.

"Your order with the reference number 16372xxxxx has been packed and the tracking number has been generated. Your order will be expedited soon."

 

 

Posted : 01/11/2023 3:36 pm
Jeggo
(@jeggo)
Estimable Member
RE: Unofficial Prusa XL Waiting Thread

The Prusa order number is the unix time stamp in seconds. 

https://www.epochconverter.com/

So thinks are moving. I can not wait to see the detailed shipping table from Prusa next week (at least it was promised for next week).

Posted : 01/11/2023 3:39 pm
Georg and dvillalba3d liked
toby.k
(@toby-k)
Trusted Member
RE: Unofficial Prusa XL Waiting Thread

Just got an email from DHL to expect the delivery Monday Nov 6 as well (to centeral Ohio).

Posted by: @area51

Got an email yesterday that my XL 5h semi assembled order was picked up by DHL (Order 16372xxxxx from November 19. 1 am 2021).
Expected delivery is Monday 6.11.2023 - time to finish the MK3S+ to MK3.9 upgrade and make room for the XL build...

 

Posted : 01/11/2023 3:43 pm
Georg
(@georg-4)
Estimable Member
RE: Unofficial Prusa XL Waiting Thread

The Prusa order number is the unix time stamp in seconds. 

Uhh…. Never thought about this! Thanks for that information. 🙂

Posted : 01/11/2023 4:07 pm
MikeH
(@mikeh)
Estimable Member
RE: Unofficial Prusa XL Waiting Thread

My 5TH, semi-assembled just shipped today: 16372, ordered 11/1//21 ~19:00 CST (as 2TH), order converted to 5TH and confirmed on 10/23/23.  Delivery estimated for 11/7/2023.

Sorry for the US dates.

Posted : 01/11/2023 5:20 pm
BillC
(@billc-2)
Active Member
RE: Unofficial Prusa XL Waiting Thread

My 5TH, semi-assembled, order #16372853xx just shipped as well. I converted on the 23rd.

Things seem to be moving along.

Posted : 01/11/2023 5:34 pm
MileHigh3Der
(@milehigh3der)
Honorable Member
RE: Unofficial Prusa XL Waiting Thread

I got mine last week, built it over the weekend.

-Had to print a new WIFI tower

-The heat bed screws were not screwed in and were loose, thought I lost one

-One head didn’t have the alignment bolts

-Fans won’t pass test unless I remove the print fan shroud.  Chat less than helpful, got the answer here. (It seems we are all BETA testers and they want us to send video for them to train their CS people with.)

 

Printed the 2 color key chain and it worked.  Tried to print a PETG piece with PLA supports- didn’t work.  Updated to new firmware.  Recalibrate heads and I’m trying speedbenchy now.  

 

Prints one material really well.  We’ll see on multi.

Posted : 01/11/2023 5:55 pm
Page 37 / 39
Share: