Notifications
Clear all

Unofficial Prusa Mini Wait Thread  

Page 184 / 241
  RSS
Jim S
(@jim-s)
New Member
RE: Unofficial Prusa Mini Wait Thread

@hawwwran

Still waiting on my 25.12.2019 order.

Posted : 11/06/2020 5:53 pm
Hawwwran
(@hawwwran)
Reputable Member
RE: Unofficial Prusa Mini Wait Thread

There were three orders marked as shipped in our spreadsheet yesterday.

One from 24.Dec (mine, whee)

One from 6.Jan

One from 26.Jan

I have come here to chew bubblegum and perfect my MINI ... and I'm all out of bubblegum.

Posted : 12/06/2020 8:04 am
Hawwwran
(@hawwwran)
Reputable Member
RE: Unofficial Prusa Mini Wait Thread

Is there a list of what to check after assembly? I know there were some issues. Is there some sort of check list somewhere?

I have come here to chew bubblegum and perfect my MINI ... and I'm all out of bubblegum.

Posted : 12/06/2020 10:32 am
Crawlerin
(@crawlerin)
Prominent Member
RE: Unofficial Prusa Mini Wait Thread

@hawwwran

You got yours finally?

I'd release 3 grub screws holding hotend and re-seat it according to this manual (release fitting by quarter turn, push hotend up, screw grub screws while holding it, tighten fitting, adjust MINDA) it may prevent underextrusion. Get extruder idler screw flush with plastic part surface, it may be too tight from factory. Checking grub screws on motor pulleys would not hurt too, there were cases reported of those being loose. Check if cables on X are not stretched too much and adjust cables as needed. When you assemble printer, make sure XZ is as perpendicular to Y as possible, both left to right and front to back, to avoid skew.

Posted : 12/06/2020 11:03 am
Hawwwran
(@hawwwran)
Reputable Member
RE: Unofficial Prusa Mini Wait Thread

@crawlerin

It should come in about an hour. I'll assamble it it t evening.

I have come here to chew bubblegum and perfect my MINI ... and I'm all out of bubblegum.

Posted : 12/06/2020 11:11 am
Steve Smith
(@steve-smith)
Trusted Member
RE: Unofficial Prusa Mini Wait Thread
Posted by: @hawwwran

@crawlerin

It should come in about an hour. I'll assamble it it t evening.

Congrats on finally getting it.. Well almost.. I installed mine and used the sample filament.. I won't make any changes to hot ends or anything else until I see an issue.. And so far it's rock solid out of the box..

My Mini has: A SuperPINDA + Bondtech Heatbreak + Bondtech Extruder installed

Posted : 12/06/2020 11:28 am
LeeM
 LeeM
(@leem)
Eminent Member
RE: Unofficial Prusa Mini Wait Thread
Posted by: @hawwwran

It finally happened. My order was just shipped. Can't believe it's real. It's DPD tho, but just in country shipping (in city, in fact).

Great news, hope you enjoy it 👍 

Posted : 12/06/2020 11:52 am
LeeM
 LeeM
(@leem)
Eminent Member
RE: Unofficial Prusa Mini Wait Thread
Posted by: @hawwwran

Is there a list of what to check after assembly? I know there were some issues. Is there some sort of check list somewhere?

I didn't do anything special to mine when I first got it, just assembled it according to the instruction book and then started printing with the supplied samples.

Posted : 12/06/2020 12:17 pm
Crawlerin
(@crawlerin)
Prominent Member
RE: Unofficial Prusa Mini Wait Thread

Lucky you guys ... I had R1 version that liked to chew MINDA cables and X carriage barely reached end of axis. I re-did all zipties just in case. Hotend was fine though, no issues there.

Posted : 12/06/2020 12:49 pm
Hawwwran
(@hawwwran)
Reputable Member
RE: Unofficial Prusa Mini Wait Thread

I got the package (for few hours now). Will post some images from unpacking for you who still need to wait.

I have come here to chew bubblegum and perfect my MINI ... and I'm all out of bubblegum.

Posted : 12/06/2020 1:26 pm
Bill Plein
(@bill-plein)
Eminent Member
RE: Unofficial Prusa Mini Wait Thread

Mine is supposed to arrive today (2 day shipping to TX USA from Prague CZ, pretty awesome). 

I'm also taking delivery of a very nice pellet smoker (Yoder YS640S) today. It's "Dad Toys Friday".

Austin, Texas, USA

Posted : 12/06/2020 2:09 pm
Hawwwran
(@hawwwran)
Reputable Member
RE: Unofficial Prusa Mini Wait Thread

I'm just preparing the assembly. Do you notice one special treat on my MINI?

I have come here to chew bubblegum and perfect my MINI ... and I'm all out of bubblegum.

Posted : 12/06/2020 4:38 pm
cwbullet
(@cwbullet)
Member
Topic starter answered:
RE: Unofficial Prusa Mini Wait Thread

@billplein

You are gonna love it.  

--------------------
Chuck H
3D Printer Review Blog

Posted : 12/06/2020 4:44 pm
burtronix
(@burtronix)
Reputable Member
RE: Unofficial Prusa Mini Wait Thread
Posted by: @hawwwran

I'm just preparing the assembly. Do you notice one special treat on my MINI?

Special treat? I don't see any Haribo. Did they substitute bubblegum just for you? 

Whatever you find to do with your hands, do with all your might!

Posted : 12/06/2020 5:54 pm
Hawwwran
(@hawwwran)
Reputable Member
RE: Unofficial Prusa Mini Wait Thread

What about on this photo?

I have come here to chew bubblegum and perfect my MINI ... and I'm all out of bubblegum.

Posted : 12/06/2020 6:03 pm
Steve Smith and Tm4n liked
Tm4n
 Tm4n
(@tm4n)
Active Member
RE: Unofficial Prusa Mini Wait Thread

@hawwwran

Nice, is that a prusa signature?

Now we know why your machine was delayed, at least 😉 

Posted : 12/06/2020 6:30 pm
Hawwwran
(@hawwwran)
Reputable Member
RE: Unofficial Prusa Mini Wait Thread
Posted by: @tm4n

@hawwwran

Nice, is that a prusa signature?

Now we know why your machine was delayed, at least 😉 

Sure it is Jo's signature 🙂

I have come here to chew bubblegum and perfect my MINI ... and I'm all out of bubblegum.

Posted : 12/06/2020 7:01 pm
Hawwwran
(@hawwwran)
Reputable Member
RE: Unofficial Prusa Mini Wait Thread

It's alive! And so silent.

I have come here to chew bubblegum and perfect my MINI ... and I'm all out of bubblegum.

Posted : 12/06/2020 7:39 pm
Bill Plein
(@bill-plein)
Eminent Member
RE: Unofficial Prusa Mini Wait Thread

My Mini was supposed to arrive today (2 day delivery from Prague to Austin TX USA) but it sat around for 12+ hours in Memphis. Which means I won't get it until Monday 🙁 

But I'm happy it's on its way so I won't complain. It would have been great to have it for the weekend, however!

Austin, Texas, USA

Posted : 12/06/2020 10:56 pm
Hawwwran
(@hawwwran)
Reputable Member
RE: Unofficial Prusa Mini Wait Thread

There was one order from 25.Dec marked as shipped in our spreadsheet yesterday.

Three orders were marked as delivered

I have come here to chew bubblegum and perfect my MINI ... and I'm all out of bubblegum.

Posted : 13/06/2020 6:54 am
Page 184 / 241
Share: