Notifications
Clear all

Welcome to our new forum! Feedback here!  

Page 21 / 23
  RSS
jsw
 jsw
(@jsw)
Famed Member
RE: Welcome to our new forum! Feedback here!

One thing that just happened to me that may be related.

I just got a notice that a reply was posted to a thread I was subscribed to.

I clicked on the link, it did bring up the correct thread, but no new posts.

Publié : 28/01/2021 1:15 pm
Oxygen
(@oxygen)
Reputable Member
RE: Welcome to our new forum! Feedback here!

I’ve seen that too, I’ve made the assumption that the user retracted there reply

Mini with FW:4.4.1 + SuperPINDA + Bondtech Heatbreak + PC4-M8 couplers + 1 piece boden

Publié : 28/01/2021 6:28 pm
örkelprint
(@orkelprint)
Eminent Member
RE: Welcome to our new forum! Feedback here!

If it was a new user it could be that his post is not yet approved by a moderator. That was my assumption when that happened. Could be just lag though..

Publié : 28/01/2021 7:22 pm
gnat
 gnat
(@gnat)
Noble Member
RE: Welcome to our new forum! Feedback here!

When I've seen that happen (been happening since they originally added notifications) the missing reply usually appears later. I've always chalked it up to server instances not being fully in sync...

MMU tips and troubleshooting
Publié : 28/01/2021 7:36 pm
cwbullet
(@cwbullet)
Membre
RE: Welcome to our new forum! Feedback here!

Not sure about the moderation.  I will say that I get notification of some post prior to them being approved.  

--------------------
Chuck H
3D Printer Review Blog

Publié : 28/01/2021 7:44 pm
jsw
 jsw
(@jsw)
Famed Member
RE: Welcome to our new forum! Feedback here!

It appears that @orkelprint is correct.  I went back to the thread and yes, the post was entered by a new user.

Publié : 29/01/2021 10:02 am
Oxygen a aimé
Oxygen
(@oxygen)
Reputable Member
RE: Welcome to our new forum! Feedback here!

@jsw, thanks for checking !

Mini with FW:4.4.1 + SuperPINDA + Bondtech Heatbreak + PC4-M8 couplers + 1 piece boden

Publié : 29/01/2021 10:22 am
cwbullet
(@cwbullet)
Membre
RE: Welcome to our new forum! Feedback here!

@jsw

That explains a lot about this situation and moderation of all new users is common.  

--------------------
Chuck H
3D Printer Review Blog

Publié : 29/01/2021 10:28 am
Plugs
(@plugs)
Eminent Member
RE: Welcome to our new forum! Feedback here!

Folks I write tom report a bug in this forum that means the Add Media button does not work (well in my Microsoft Edge anyway) . I will attach a screen cam of the behaviour as I try and put an mp4 in this post so you can see the result. I will then attach the mp4 of the screen cam . 

 

So here we go ..........

 

So the add media button added the above text that does nothing

And I have attached the screencam of the operation

Attachment removed
Ce message a été modifié il y a 4 years 2 fois par Plugs
Publié : 18/02/2021 5:48 pm
MadCyborg
(@madcyborg)
Eminent Member
RE: Welcome to our new forum! Feedback here!

Is there a way to jump from the (sub-)forum overview directly to the latest unread post of a thread?

Publié : 19/03/2021 12:27 pm
cwbullet
(@cwbullet)
Membre
RE: Welcome to our new forum! Feedback here!

@madcyborg

Not that I am tracking.  

--------------------
Chuck H
3D Printer Review Blog

Publié : 19/03/2021 12:32 pm
draeh
(@draeh)
Active Member
RE: Welcome to our new forum! Feedback here!
Posted by: @madcyborg

Is there a way to jump from the (sub-)forum overview directly to the latest unread post of a thread?

^ This and a per sub-forum 'mark all read'.

The only one I've found is the one at the footer of the page and it marks the entire Prusa forum read.

Publié : 19/03/2021 1:56 pm
--
 --
(@)
Illustrious Member
RE: Welcome to our new forum! Feedback here!

Ya know - if Prusa gave a Mini kit to a few of their more prolific unpaid helpers that spend time on these forums, they might have better help in the Mini forums. Just an idea ... don't shoot the messenger.

Publié : 10/05/2021 9:43 pm
cwbullet
(@cwbullet)
Membre
RE: Welcome to our new forum! Feedback here!

@tim-2

Yup.  They could send me a printer and I would gladly be a more productive member of the forum.  

--------------------
Chuck H
3D Printer Review Blog

Publié : 11/05/2021 2:00 am
MysDawg a aimé
jerrodclement
(@jerrodclement)
New Member
Good work

Well things look to be pretty good and it's a solid forum for information.

Publié : 06/09/2021 10:37 am
MysDawg
(@mysdawg)
Estimable Member
RE: Welcome to our new forum! Feedback here!

I stop by daily for my morning reading....

Publié : 07/09/2021 10:00 pm
Sandersann
(@sandersann)
Active Member
Very informative

One of the things that convinced me to get a Prusa was the community interaction as demonstrated in the forums. I have found most of the solutions to my issues as a new Prusa Mini user without even asking questions. Users here are very helpful and generally cordial.

 

Publié : 24/10/2021 3:35 am
JoanTabb
(@joantabb)
Veteran Member Moderator

Welcome to the community

regards Joan

I try to make safe suggestions,You should understand the context and ensure you are happy that they are safe before attempting to apply my suggestions, what you do, is YOUR responsibility. Location Halifax UK

Publié : 24/10/2021 7:49 am
towlerg
(@towlerg)
Noble Member
RE: Pretty please allow .3MF attacments.

Prusa Prusa Prusa will you please allow .3MF as a valid attachment type. Whats the point of the boss (quite rightly) publishing a piece berating .STL only to prevent it's obvious replacement being directly available to the user-to-user community. 

Ce message a été modifié il y a 3 years par towlerg
Publié : 24/10/2021 11:39 am
Area51 et Ringarn67 ont aimé
FoxRun3D
(@foxrun3d)
Famed Member
RE: +1

Would cut the number of posts where we need to explain why and how to zip up 3mf files dramatically. 

And it's probably just a 2 minute task for a programmer to add it to a config file. 

Formerly known on this forum as @fuchsr -- until all hell broke loose with the forum software...

Publié : 24/10/2021 12:05 pm
Page 21 / 23
Partager :