Avisos
Vaciar todo

Prusa Mini Clone from China  

Página 14 / 18
  RSS
cwbullet
(@cwbullet)
Miembro
Topic starter answered:
RE: Prusa Mini Clone from China

@goszu

Can you or some one else measure the height of the hexagonal bed spacers that came with the kit?  

--------------------
Chuck H
3D Printer Review Blog

Respondido : 09/11/2020 2:51 pm
cwbullet
(@cwbullet)
Miembro
Topic starter answered:
RE: Prusa Mini Clone from China

If anyone has the measurements of the spacers, I love to have them.  

I am going close with one more finding that would drive me to order an Orginal Prusa Mini kit over this one.  I started printing and noticed the prints are just not right in the center.  I thought the bed appears to be not level, but that is not it.  The screws are too tall attacking the heat bed so it pushes the sheet up a little.   

--------------------
Chuck H
3D Printer Review Blog

Respondido : 10/11/2020 2:32 am
rockytoptim
(@rockytoptim)
Trusted Member
RE: Prusa Mini Clone from China

@charles-h13

Charles,

I didn't have a spare so i measured one on my mini.  It measured 5.8mm. I hope this helps.

 

Esta publicación ha sido modificada el hace 4 years por rockytoptim
Respondido : 10/11/2020 5:19 am
Robert
(@robert-14)
Eminent Member
RE: Prusa Mini Clone from China

@charles-h13

5mm on my clone

Respondido : 10/11/2020 4:21 pm
cwbullet
(@cwbullet)
Miembro
Topic starter answered:
RE: Prusa Mini Clone from China

@goszu

Thank you.  

--------------------
Chuck H
3D Printer Review Blog

Respondido : 11/11/2020 3:46 am
cwbullet
(@cwbullet)
Miembro
Topic starter answered:
RE: Prusa Mini Clone from China

First benchie 

My first benchie on the clone.  Need to dial it in a little more.  

--------------------
Chuck H
3D Printer Review Blog

Respondido : 11/11/2020 3:50 am
cwbullet
(@cwbullet)
Miembro
Topic starter answered:
RE: Prusa Mini Clone from China

 

Another test print

--------------------
Chuck H
3D Printer Review Blog

Respondido : 11/11/2020 11:00 pm
Nikolai
(@nikolai)
Noble Member
RE: Prusa Mini Clone from China

Looks like Z banding on some layers.

Often linked posts:
Going small with MMU2
Real Multi Material
My prints on Instagram

Respondido : 11/11/2020 11:05 pm
cwbullet
(@cwbullet)
Miembro
Topic starter answered:
RE: Prusa Mini Clone from China

@nikolai-r

Sure does.

--------------------
Chuck H
3D Printer Review Blog

Respondido : 11/11/2020 11:16 pm
karl-herbert
(@karl-herbert)
Illustrious Member
RE: Prusa Mini Clone from China

@charles-h13

Looks more like Josef's pug Buddy 😎 

Statt zu klagen, dass wir nicht alles haben, was wir wollen, sollten wir lieber dankbar sein, dass wir nicht alles bekommen, was wir verdienen.

Respondido : 11/11/2020 11:19 pm
cwbullet
(@cwbullet)
Miembro
Topic starter answered:
RE: Prusa Mini Clone from China

@karl-herbert

I am actually happy with the quality.  I need a little more fine-tuning, but not bad.  

--------------------
Chuck H
3D Printer Review Blog

Respondido : 12/11/2020 2:24 am
karl-herbert
(@karl-herbert)
Illustrious Member
RE: Prusa Mini Clone from China

@charles-h13

I like this gnome 👍 would you please send me a link?

Thanks!

Statt zu klagen, dass wir nicht alles haben, was wir wollen, sollten wir lieber dankbar sein, dass wir nicht alles bekommen, was wir verdienen.

Respondido : 12/11/2020 2:44 am
karl-herbert
(@karl-herbert)
Illustrious Member
RE: Prusa Mini Clone from China

I have tested this board (just board) on the Mini for fun. Works perfectly so far, almost identical to the original. The board version is not 1.0.2 but 1.0.0.
Let's see how it works in the long run:

https://www.aliexpress.com/item/4001237541591.html?spm=a2g0s.9042311.0.0.3da24c4dv40yKl

 

Statt zu klagen, dass wir nicht alles haben, was wir wollen, sollten wir lieber dankbar sein, dass wir nicht alles bekommen, was wir verdienen.

Respondido : 26/11/2020 8:28 pm
cwbullet
(@cwbullet)
Miembro
Topic starter answered:
RE: Prusa Mini Clone from China
Posted by: @karl-herbert

I have tested this board (just board) on the Mini for fun. Works perfectly so far, almost identical to the original. The board version is not 1.0.2 but 1.0.0.
Let's see how it works in the long run:

https://s.click.aliexpress.com/e/_Apus1 m" target="true"> https://www.aliexpress.com/item/4001237541591.html?spm=a2g0s.9042311.0.0.3da24c4dv40yKl

 

This set of controller board and display are on sale for Black Friday.  I have been printing for a week with good success.  It led me to order another Orginial Prusa Mini.  I will say that FSTEC Mini does not come with an all-metal hotend.  If you remember in this thread that I had an all-metal installed on mine.   I remember pulling out two hotends and I install the one from my storage and not the kit.  This errantly made me think it was all-metal.  When I dug through the drawer, I found the other hotend and it is not all-metal.  I realized the mistake this week.  

--------------------
Chuck H
3D Printer Review Blog

Respondido : 26/11/2020 8:58 pm
karl-herbert
(@karl-herbert)
Illustrious Member
RE: Prusa Mini Clone from China

@cwbullet

What exactly is the difference between the original all metall hotend and the one that came with the kit?

 

Statt zu klagen, dass wir nicht alles haben, was wir wollen, sollten wir lieber dankbar sein, dass wir nicht alles bekommen, was wir verdienen.

Respondido : 26/11/2020 9:13 pm
Crawlerin
(@crawlerin)
Prominent Member
RE: Prusa Mini Clone from China

@karl-herbert

It's jist a metal pipe with thread at the end, PTFE runs all the way through. I described it in this post: https://forum.prusa3d.com/forum/general-discussion-announcements-and-releases/prusa-mini-clone-from-china/paged/12/#post-293659 see comparison between photos here and blueprint on GitHub.

BTW I am very happy they (Prusa) offer official DIY kit now.

Respondido : 26/11/2020 9:24 pm
karl-herbert
(@karl-herbert)
Illustrious Member
RE: Prusa Mini Clone from China

@crawlerin

The assembly is no problem even without instructions. You only have to proceed carefully, as with the MK series. But I would use a different extruder. The filament sensor is not necessarily needed. And I am curious what the super new superpinda will offer.

Statt zu klagen, dass wir nicht alles haben, was wir wollen, sollten wir lieber dankbar sein, dass wir nicht alles bekommen, was wir verdienen.

Respondido : 26/11/2020 9:40 pm
cwbullet
(@cwbullet)
Miembro
Topic starter answered:
RE: Prusa Mini Clone from China

@karl-herbert

I have to concur.  I think the Mini Kit from Pursa is gonna be a big seller.  

--------------------
Chuck H
3D Printer Review Blog

Respondido : 26/11/2020 9:48 pm
cwbullet
(@cwbullet)
Miembro
Topic starter answered:
RE: Prusa Mini Clone from China

I got another clone.  Reportedly it is one of 25 from Triangle Labs.  I am not sure I like it.  It has a V6 hotend and ti came assembled.  

--------------------
Chuck H
3D Printer Review Blog

Respondido : 02/12/2020 2:45 am
Andrew Pawelski
(@andrew-pawelski)
Trusted Member
RE: Prusa Mini Clone from China

@cwbullet

How much do they sell for why don’t u  like it

 

 

Respondido : 02/12/2020 10:07 am
Página 14 / 18
Compartir: