Notifications
Clear all

New Firmware release candidate available (v4.1.0 RC1)  

Page 1 / 2
  RSS
Gordon W
(@gordon-w)
Reputable Member
New Firmware release candidate available (v4.1.0 RC1)

https://github.com/prusa3d/Prusa-Firmware-Buddy/releases/tag/v4.1.0-RC1

Posted : 19/06/2020 5:00 pm
Oxygen
(@oxygen)
Reputable Member
RE: New Firmware release candidate available (v4.1.0 RC1)

I'm reading the realease notes, a lot of great stuff there... (impressed)

 

Mini with FW:4.4.1 + SuperPINDA + Bondtech Heatbreak + PC4-M8 couplers + 1 piece boden

Posted : 19/06/2020 5:02 pm
Gordon W
(@gordon-w)
Reputable Member
Topic starter answered:
RE: New Firmware release candidate available (v4.1.0 RC1)

From the release notes, a summary of the changes;

  • Improved behavior after USB drive removal
  • Marlin Card Reader replaced
  • Printer acoustic signalization
  • Filament load/unload procedure adjusted
  • Preheat function improved
  • Tune menu extended
  • File browser improved
  • Horizontal scrolling text
  • Octoprint screen improved
  • Watchdog dump feature
  • Support for NTP servers
  • Safety measures for filament load/unload
  • Reworked temperature regulation
  • Bug fixes
Posted : 19/06/2020 5:06 pm
seishin
(@seishin)
Active Member
RE: New Firmware release candidate available (v4.1.0 RC1)

> Safety measures for filament load/unload

not loving this feature 😛
I mean when loading fails, I won't be able to do another "Load" straight afterwards, although I see the notes on improved load/unload procedures, so maybe this'll go smoother 🙂

nonetheless, overall great job!!

Posted : 20/06/2020 9:32 am
towlerg
(@towlerg)
Noble Member
RE: New Firmware release candidate available (v4.1.0 RC1)

"acoustic signalization" surely theres a less clunky way to phrase that!

Posted : 20/06/2020 2:47 pm
SS220
(@ss220)
Estimable Member
RE: New Firmware release candidate available (v4.1.0 RC1)

Nothing about the ability to save updated e-steps?

Posted : 20/06/2020 4:00 pm
Texy
 Texy
(@texy)
Reputable Member
RE: New Firmware release candidate available (v4.1.0 RC1)

Thanks for the heads-up. Looking good so far, although I noticed that the z-level is constantly changing on the screen (when its still on one layer).

Texy

Posted : 22/06/2020 12:06 pm
Texy
 Texy
(@texy)
Reputable Member
RE: New Firmware release candidate available (v4.1.0 RC1)

Ah - it has already been reported.... https://github.com/prusa3d/Prusa-Firmware-Buddy/issues/608

Texy

Posted : 22/06/2020 12:07 pm
jweaver
(@jweaver)
Honorable Member
RE: New Firmware release candidate available (v4.1.0 RC1)

Just did the upgrade.. The "sound" needs some work... Did I imagine it, or didn't the Mini make nice little clicks and short beeps before?

Now all the beeps are long.. Lound and Once seem the same.. So I went for Silent and was surprised that whilst loading the filament I had a low gravelly beep.. What do they think the word "silent" means? Surely this should disable ALL sounds?

I don't want it silent.. But I wasn nice little quick beeps...... What was it like before? I can't remember now..

Posted : 22/06/2020 2:46 pm
Gordon W
(@gordon-w)
Reputable Member
Topic starter answered:
RE: New Firmware release candidate available (v4.1.0 RC1)

@jweaver

You're not alone having 'concerns' about the changes to the sound! https://github.com/prusa3d/Prusa-Firmware-Buddy/issues/603

Posted : 22/06/2020 2:54 pm
jweaver
(@jweaver)
Honorable Member
RE: New Firmware release candidate available (v4.1.0 RC1)

Cheers... did i imagine it, or did rotating the wheel used to give a tiny little “click”? 

Posted : 22/06/2020 2:59 pm
Crawlerin
(@crawlerin)
Prominent Member
RE: New Firmware release candidate available (v4.1.0 RC1)

That's a lot of improvements. Looking forward to better USB navigation and loading/unloading filament.

Disclaimer: Even though the printer is capable of resuming the print after the USB drive is disconnected, it is recommended to keep the drive plugged in throughout the entire print. Disconnecting the USB drive and rewriting or adjusting the printed file might lead to unpredictable results.

🧐 🤔😈 I can see this going some unpredictable ways ... on purpose.

Posted : 22/06/2020 8:19 pm
Izmet Fekali
(@izmet-fekali)
Active Member
RE: New Firmware release candidate available (v4.1.0 RC1)

I like the improvements, however, it is still not possible to get out of the Octoprint screen on a filament change in the middle of the print. Or am I missing something?

Posted : 24/06/2020 10:47 pm
Texy
 Texy
(@texy)
Reputable Member
RE: New Firmware release candidate available (v4.1.0 RC1)
Posted by: @jonas-1

I like the improvements, however, it is still not possible to get out of the Octoprint screen on a filament change in the middle of the print. Or am I missing something?

Not sure what you mean? Which octoprint screen - on your browser, the MINI, or the web interface?

Posted : 25/06/2020 1:22 am
Izmet Fekali
(@izmet-fekali)
Active Member
RE: New Firmware release candidate available (v4.1.0 RC1)

The screen on the Mini (when connected to Octoprint, it shows the green octopus logo.) 

This post was modified 4 years ago by Izmet Fekali
Posted : 25/06/2020 1:37 am
jweaver
(@jweaver)
Honorable Member
RE: New Firmware release candidate available (v4.1.0 RC1)

The beeps are really annoying me.. Even set to Silent, I still get to long, loud beeps during loading... Prusa should look up the word "silent" in the dictionary... I know its an RC so can't blame them.. I just hope its fixed before the final release.

I was also disappointed that they havn't changed the "reprint" option after printing.. I want the default option to be "home".. I am much more likely to go to the home menu, than reprint..  WHen I come back to the printer after printing, I almost always kick of a reprint and it annoys me.

I raised an issue on GitHub and got the idea that this would be fixed.. But there is no change.

Posted : 25/06/2020 10:53 am
Dronitoni
(@dronitoni)
Eminent Member
RE: New Firmware release candidate available (v4.1.0 RC1)

@jweaver

I support the "noise issue" on Github.

It's basically annoying.

Posted : 27/06/2020 7:26 pm
Area51
(@area51)
Member
RE: New Firmware release candidate available (v4.1.0 RC1)
Posted by: @jweaver

I was also disappointed that they havn't changed the "reprint" option after printing.. I want the default option to be "home".. I am much more likely to go to the home menu, than reprint..  WHen I come back to the printer after printing, I almost always kick of a reprint and it annoys me.

I raised an issue on GitHub and got the idea that this would be fixed.. But there is no change.

I totally agree, Home should be the default option after print, not re-print. I can't remember ever doing a reprint, without first changing something in the slicer.

Have a look at my models on Printables.com 😉

Posted : 28/06/2020 1:04 am
Dronitoni
(@dronitoni)
Eminent Member
RE: New Firmware release candidate available (v4.1.0 RC1)

For me, the subject of the annoying beeping  is finished.

My solution is, I have glued a big sticky tape on the beeper. The beeper is easily accessible on the back of the control unit.

Now it is finally quiet. 😊 😊 😊 

Posted : 01/07/2020 7:13 pm
Gary
 Gary
(@gary-9)
New Member
RE: New Firmware release candidate available (v4.1.0 RC1)

I’m new to this game, so maybe this is my lack of understanding - but my mini has crashed several times in the first couple of weeks of using it and when the system reboots the values for each axis seem to be way off. This has led to several heart stopping moments of the print head smashing into the end stops and grinding stepper motors. Worst of all has been me inadvertently moving the z axis and not realising the values were completely out - now I have an immaculate circular dent in the PEI sheet from the nozzle 👎

So, it would be good if the firmware could include a fix for this - e.g. on system reboot following a crash the user is made to perform auto home calibration to reset accurate values for each axis?

Posted : 05/07/2020 10:21 pm
Page 1 / 2
Share: