RE: MK4 Printable Parts
those turned out nice!
My first couple parts in Bambu PETG-CF 🙂
RE: MK4 Printable Parts
Making progress!
RE: MK4 Printable Parts
those turned out nice!
My first couple parts in Bambu PETG-CF 🙂
Thanks, yours as well!
RE: MK4 Printable Parts
Making progress! Too bad the MK3S+ -> MK4 kits don't ship until june...
RE: MK4 Printable Parts
nice collection of parts you have there...started the print process now for the Mark IV...I have two parts so far printed; tweaked the infill to 25%
RE: MK4 Printable Parts
Nice color too - that should look pretty sweet when its all installed!
Making progress! Too bad the MK3S+ -> MK4 kits don't ship until june...
--> MK4 - MK4S - MINI+ - MMU3 - Accelerometer Guide - BambuLab A1 Combo <--
RE: MK4 Printable Parts
Yeah, should brighten things up a bit. My two printers currently use Autobot blue and Decepticon purple PETG from Paramount 3D. I'll have to wait for my 5 extruder XL to get in before I try to do a multi-color printer in ABS. pretty sure the MMU won't be happy doing bvoh + abs lol.
Nice color too - that should look pretty sweet when its all installed!
Making progress! Too bad the MK3S+ -> MK4 kits don't ship until june...
RE: MK4 Printable Parts
Just sliced what I think is the last batch of parts. now it's waiting time.
RE:
Just sliced what I think is the last batch of parts. now it's waiting time.
Nice I think I have all of mine done too! Still wondering if I should just buy the kit as it's not terribly more expensive, not sure what I'll do with this printers old parts otherwise.
I did a few vents in PC-CF and ASA, the rest of the parts were done with PETG-CF on my Bambu X1C
RE: MK4 Printable Parts
looking good! I had to reprint the shrouds because I broken them trying to remove the support material. I think I've got the complete set of parts for two printers. I'll take a complete inventory before I start disassembling printers lol so annoying those upgrade kits don't start shipping until june.
RE: MK4 Printable Parts
Here is a good riddle; just how many parts should be re-printed from R1 now that my printer upgrade is about to ship?
It looks like most have at least hit R2 with some I spotted with R3.
RE: MK4 Printable Parts
I reprinted them all.
RE: MK4 Printable Parts
I figured that might be the case. I did blow out the extruder on the MK III, but I do have a backup printer that I can use to start having fun. Hmm; I might just select a different color combo. By blow out; some of the plastic parts had cracked....
Sort of thinking I am in for a pinch in for a pound - so any other specific upgrade parts that are highly recommended?
Or was that in for a farthing, in for a pound... 😉
RE: MK4 Printable Parts
I replaced the x and y rods and bearings with brand new ones on both my MK3S printers at the same time I did the upgrade for them. Things are great so far. I love the new color too lol I did end up printing the y rod holders in the orange prusament PETG vs the ABS though. ABS doesn't like the bending when you tighten the y rod holders down and PETG is more tolerant. But I love the new look though.
This one was taken before I swapped the y rod holders for orange prusment petg. This was also the first one I did. shows me printing ninjaflex tpu. So far I've been very happy with the upgrades.
This is what I printed in.
https://www.hatchbox3d.com/products/3d-abs-1kg1-75-365c
RE: MK4 Printable Parts
my bad, the above picture was my first print with PLA.
Here's first print with ninjaflex
I've not yet tried printing with ABS or ASA again since I have to wheel the thing over to the window but there's a thread on the forum here that folks are getting curled edges possibly due to the airflow of the part cooling heat sink fans.