ssill2 – Activité – Prusa3D Forum

Notifications

Clear all

ssill2

Groupe: Enregistré

A(ont) rejoint: 2021/01/18

Noble Member

	@ringarn67 Seems so. Take notice of the dialog in the botto... Dans le forum How do I print this? (Printing help)	il y a 4 years
	So I actually verified that in 2.4.0 this doesn't happen. i... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@ringarn67 You should just need to add a new issue. The mor... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@ringarn67 Test.3mf also opens with E3D Edge as the filament... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@ringarn67 I can confirm that after removing that built in p... Dans le forum How do I print this? (Printing help)	il y a 4 years
	And if I open the config wizard to add filaments, here are m... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@ringarn67 Here's my list of filaments that are padlocked Dans le forum How do I print this? (Printing help)	il y a 4 years
	@swiss_cheese I've had zero issues with compatibility from o... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@swiss_cheese No worries lol. I'm always about trying out ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Ok I had a chance to open this. it looks normal to me. th... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@ringarn67 That could be a bug since the built in filament w... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@swiss_cheese Yah no prob. I’ll try to open in am Dans le forum How do I print this? (Printing help)	il y a 4 years
	@swiss_cheese I don’t have any overture tpu or I’d give it a... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@swiss_cheese I can't stand doing tpu lol, but my wife seems... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@swiss_cheese another satisfied customer 🙂 Dans le forum How do I print this? (Printing help)	il y a 4 years
	@swiss_cheese well, if I learned anything it's from the fila... Dans le forum How do I print this? (Printing help)	il y a 4 years
	You might try grabbing the settings from this project I did ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@swiss_cheese Nice! Showing again that your moniker is wel... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I'm using the prusament profiles. so far after the couple, ... Dans le forum General discussion, announcements and releases	il y a 4 years
	@baklin Yeah I'm a java developer, not a C++ dev lol, but I ... Dans le forum General discussion, announcements and releases	il y a 4 years

Page 74 / 100 Précédent Suivant

Statistiques du forum

595 Forums

68.9 K Sujets

481.8 K Messages

11 En-ligne

77.5 K Membres

Le dernier des messages: Really, Prusa? Notre nouveau membre: HaydenWizard Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé