ssill2 – Activité – Prusa3D Forum

Notifications

Clear all

ssill2

Groupe: Enregistré

A(ont) rejoint: 2021/01/18

Noble Member

	@xayoz Here's the commands I ran. These are run from the bu... Dans le forum General discussion, announcements and releases	il y a 4 years
	I had to read the instructions carefully but I ended up gett... Dans le forum General discussion, announcements and releases	il y a 4 years
	As with my previous PETG + BVOH sojourn, the X through the ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	So the filament switches seem to be ok. However, I'm running... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@axion Look at the sides. Those should be relatively smooth... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I can't tell but it seems like the density is used for estim... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@axion yeah obviously if there is a specific profile for it ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I'm also feeding both filaments from filament dryers that ar... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I did one of these the other day to test soluble support mat... Dans le forum How do I print this? (Printing help)	il y a 4 years
	and of course I have 27h more to go on one printer and I jus... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I'm not sure, but those square pegs look suspect and may be ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Ok, I'm getting back to this. About to try this model In En... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@axion it had just gotten the first layer down. so not much... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@axion I just started it printing a bit ago, but I'm going t... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@axion yeah I'm guessing the amount of infill as well. 5% m... Dans le forum How do I print this? (Printing help)	il y a 4 years
	the square pegs look pretty rough too. and they don't in th... Dans le forum How do I print this? (Printing help)	il y a 4 years
	How did you make that model? Besides that, 5% infill looks... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@axion The model looks strange when sliced you do have 7 to... Dans le forum How do I print this? (Printing help)	il y a 4 years
	you might zip up your .3mf file and attach here so folks can... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@ringarn67 I had the same issue and a thorough scrub with da... Dans le forum How do I print this? (Printing help)	il y a 4 years

Page 64 / 100 Précédent Suivant

Statistiques du forum

595 Forums

68.8 K Sujets

481.5 K Messages

14 En-ligne

77.4 K Membres

Le dernier des messages: Core One, using the texture sheet and no way to change Z axis Notre nouveau membre: mike Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé