ssill2 – Actividad – Prusa3D Forum

Avisos

Vaciar todo

ssill2

Grupo: Registrado

Registrado: 2021/01/18

Noble Member

	glue stick will definitely do the trick. Layerneer Bed Weld... En el foro How do I print this? (Printing help)	hace 3 years
	I've never had the problem with PLA. The smooth sheet is re... En el foro How do I print this? (Printing help)	hace 3 years
	Here you go. see attached .zip LCD-cover-ORIGINAL-... En el foro How do I print this? (Printing help)	hace 3 years
	Let me see if I can dig up what I printed those with En el foro How do I print this? (Printing help)	hace 3 years
	I edited the model so the lettering would be flush. En el foro How do I print this? (Printing help)	hace 4 years
	be sure to remember to switch your selected sheet profile to... En el foro How do I print this? (Printing help)	hace 4 years
	PETG with BOVH can work, but I find that the problem comes f... En el foro How do I print this? (Printing help)	hace 4 years
	It entirely depends. If you're doing strictly PLA with diff... En el foro How do I print this? (Printing help)	hace 4 years
	I've been pretty busy with work so I've kind of slowed down ... En el foro How do I print this? (Printing help)	hace 4 years
	I've not tried polysmooth myself, but I've liked the other p... En el foro How do I print this? (Printing help)	hace 4 years
	As mentioned above, the printer firmware will allow you to c... En el foro How do I print this? (Printing help)	hace 4 years
	I'm not sure. The scrubbing with hot water and dawn usually... En el foro How do I print this? (Printing help)	hace 4 years
	I would recommend posting some pictures and perhaps a zipped... En el foro How do I print this? (Printing help)	hace 4 years
	you could try increasing heat a bit. Any backpressure at al... En el foro How do I print this? (Printing help)	hace 4 years
	Which sheet are you using? Smooth? You should use glue st... En el foro How do I print this? (Printing help)	hace 4 years
	the idler bolt is super simple and I find I don't have to ch... En el foro How do I print this? (Printing help)	hace 4 years
	I find that with PETG I have a different zOffset, and a sepa... En el foro How do I print this? (Printing help)	hace 4 years
	What nessuno and bob said. 100mm 1 layer(.2mm) square on a... En el foro How do I print this? (Printing help)	hace 4 years
	You might also try lowering the temp just a little. It's a... En el foro How do I print this? (Printing help)	hace 4 years
	So generally you'll want to: - Make sure your idler bolt is ... En el foro How do I print this? (Printing help)	hace 4 years

Página 44 / 103 Anterior Siguiente

Estadísticas del Foro

595 Foros

69.8 K Temas

488.4 K Respuestas

15 En línea

80.3 K Miembros

Último Mensaje: My turn getting a Core 1+ working Nuestro miembro más reciente: Hinagea Últimos Mensajes Publicaciones sin leer Etiquetas

Iconos del foro: El foro no contiene publicaciones sin leer El foro contiene publicaciones sin leer

Iconos de los Temas: No respondidos Respondido Activo Popular Fijo No aprobados Resuelto Privado Cerrado