ryan.f15 – Activité – Prusa3D Forum

Notifications

Clear all

ryan.f15

Groupe: Enregistré

A(ont) rejoint: 2017/10/25

Estimable Member

	@3delight My printer has 12v fans. I bought it a couple yea... Dans le forum Hardware, firmware and software help	il y a 4 years
	Replacement print fan options Dans le forum Hardware, firmware and software help	il y a 4 years
	MK2 backplate when printing PETG warps Dans le forum Hardware, firmware and software help	il y a 4 years
	Anybody? Dans le forum How do I print this? (Printing help)	il y a 4 years
	OK, tried a brand new spool, I'm getting adhesion, and a few... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Oh, this is an MK2.5 kit from an MK2 kit. Dans le forum How do I print this? (Printing help)	il y a 4 years
	Did another print, cleaned surface with 91% IPA before. Sam... Dans le forum How do I print this? (Printing help)	il y a 4 years
	The other pic 20210226_112135.jpg Dans le forum How do I print this? (Printing help)	il y a 4 years
	@clemens-m This is a brand new sheet that I have cleaned wit... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Yeah but I just tried to print something off and the left ed... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@clemens-m Sorry. Here's -0.795 20210226_095318.j... Dans le forum How do I print this? (Printing help)	il y a 4 years
	OK well I dialed it all the way down to -0.765 and it got me... Dans le forum How do I print this? (Printing help)	il y a 4 years
	-0.710 same thing Dans le forum How do I print this? (Printing help)	il y a 4 years
	I have the v2 with the 2.5 upgrade kit. So wold I increase ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	This is at -0.690. It isn't a solid square, when I peel it ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Here's the surface. It's -0.680 in the top left and bottom ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	This is -0.680. I'm doing the calibration surface now ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Here's -0.660: 20210224_223044.jpg It's reasonably stic... Dans le forum How do I print this? (Printing help)	il y a 4 years
	OK well I tried -0.650. The first layer cal isn't sticking ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@bobstro I'll try that tonight. My problem is that at any h... Dans le forum How do I print this? (Printing help)	il y a 4 years

Page 2 / 7 Précédent Suivant

Statistiques du forum

559 Forums

63.1 K Sujets

444 K Messages

20 En-ligne

68.1 K Membres

Le dernier des messages: Why is the startup so bloody slow?!? Notre nouveau membre: etiennep Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé