richard.l – Activité – Prusa3D Forum

Notifications

Clear all

richard.l

Groupe: Modérateur

A(ont) rejoint: 2015/10/29

Titre: Membre Moderator

	George Best to use anti-vibration feet. They lift the corn... Dans le forum Prusa i3 kit (Archive)	il y a 9 years
	Peter While I don't disagree sometimes the original supplie... Dans le forum Prusa i3 kit (Archive)	il y a 9 years
	Basilio I have 2 of those exact ones being delivered by UPS... Dans le forum Prusa i3 kit (Archive)	il y a 9 years
	Actually, the replacement fan would be 30x30x10 mm in either... Dans le forum Prusa i3 kit (Archive)	il y a 9 years
	Nigel The filament is used to hold the wire bundle up so it... Dans le forum Prusa i3 kit (Archive)	il y a 9 years
	Makes me wonder if spray starch used for ironing would work. Dans le forum Print tips (Archive)	il y a 9 years
	Nigel Trust me, the filament will break. Has happened to me... Dans le forum Prusa i3 kit (Archive)	il y a 9 years
	Peter, Don't know why I didn't think of that! Will try when... Dans le forum Prusa i3 kit (Archive)	il y a 9 years
	Is there a replacement for the 3mm filament that can be used... Dans le forum Prusa i3 kit (Archive)	il y a 9 years
	Hi Richard, Did you get the test protocol with the printer? ... Dans le forum Prusa i3 kit (Archive)	il y a 9 years
	After building a 12"x12"x16" printer with a heated bed I hig... Dans le forum Prusa i3 kit (Archive)	il y a 9 years
	As Peter said on point 1, also make sure the tension screws ... Dans le forum Print tips (Archive)	il y a 9 years
	Scott, I'm going to guess the part fan turns on at the seco... Dans le forum Prusa i3 kit (Archive)	il y a 10 years
	I have ZERO design skills. 😥 I have been looking for a... Dans le forum Prusa i3 kit (Archive)	il y a 10 years
	Peter Yeah, I just realized after reading your post that I ... Dans le forum Prusa i3 kit (Archive)	il y a 10 years
	Where can I find the stl for the original part fan? I have a... Dans le forum Prusa i3 kit (Archive)	il y a 10 years
	Speaking from experience, that is the PTFE tube needing to b... Dans le forum Prusa i3 kit (Archive)	il y a 10 years
	I'm with Peter on this. I spent a couple days looking over t... Dans le forum Improvements (Archive)	il y a 10 years
	Peter According to raspberrypi.org, the pi2 B draws a max o... Dans le forum Improvements (Archive)	il y a 10 years
	That would be me! I use the connector in the purple box to s... Dans le forum Improvements (Archive)	il y a 10 years

Page 33 / 37 Précédent Suivant

Statistiques du forum

585 Forums

68.3 K Sujets

478.3 K Messages

10 En-ligne

76.1 K Membres

Le dernier des messages: The Cryogrip Pro Glacier plate is an excellent cheaper alternative to the Satin plate with one minor caveat on the Core One Notre nouveau membre: ArtiVIVO Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé