renegadesk – Activity – Prusa3D Forum

Notifications

Clear all

renegadesk

Group: Registered

Joined: 2015/09/27

Estimable Member

	michal.v Vyborny nápad a je to pekné ! Nerezonuje to drev... In forum Nápady na zlepšení (Archiv)	10 years ago
	When you are preparing to generate g-code in slicer make sur... In forum Prusa i3 kit (Archive)	10 years ago
	Ale problém už nevyzerá byt v skle 🙄 Ono sa zohne len ... In forum Stavebnice Prusa i3 (Archiv)	10 years ago
	Som rád že sa ti to podarilo vytlačiť nakoniec 🙂 In forum Nejlepší výtisky & tiskové tipy	10 years ago
	Ani mne to nesedelo perfektne. ale orezovátkom novym to skus... In forum Stavebnice Prusa i3 (Archiv)	10 years ago
	I have the same problem with heatbed. It makes the glass not... In forum Prusa i3 kit (Archive)	10 years ago
	Myslám že je to tak nadizajnované naschvál, Na niektorých CN... In forum Stavebnice Prusa i3 (Archiv)	10 years ago
	Pekné, tá píštalka píska silno? Páči sa mi 😀 trošku slabš... In forum Nejlepší výtisky & tiskové tipy	10 years ago
	When I see something going wrong I dont waste time by going ... In forum Prusa i3 kit (Archive)	10 years ago
	Alebo to skusit s tym raftom (ešte som to neskušal) , ale ... In forum Rady k tisku (Archiv)	10 years ago
	Skus to vytlačiť na dve časti alebo na 4 , model nebude taky... In forum Rady k tisku (Archiv)	10 years ago
	💡 Presne to lajkovacie tlačítko by bodlo 😀 Fakt super ... In forum Nejlepší výtisky & tiskové tipy	10 years ago
	Ale problém už nevyzerá byt v skle 🙄 Ono sa zohne len ... In forum Stavebnice Prusa i3 (Archiv)	10 years ago
	Nove sklo bolo o trošku rovnejšie, ale avšak stále mám jeden... In forum Stavebnice Prusa i3 (Archiv)	10 years ago
	I have personally printed them in ABS with 0,2 layer height ... In forum Prusa i3 kit (Archive)	10 years ago
	Its normal, It was designed this way to only go around 100 d... In forum Prusa i3 kit (Archive)	10 years ago
	Naparadu 😀 takže naspäť v akcii 😀 odkial máš model prosí... In forum Nejlepší výtisky & tiskové tipy	10 years ago
	The board did the homing for X axis so it should not be wro... In forum Prusa i3 kit (Archive)	10 years ago
	Tak som rád že sa aspoň prišlo na to kde je ten problém. :id... In forum Rady k tisku (Archiv)	10 years ago
	By using bussines card to calibrate you are actualy putting ... In forum Software (Archive)	10 years ago

Page 6 / 8 Prev Next

Forum Statistics

585 Forums

68.2 K Topics

477.4 K Posts

12 Online

75.9 K Members

Latest Post: Buddy Camera in the Core one reads the code and shows up in Connect, but is not registered. Our newest member: mnentwig Recent Posts Unread Posts Tags

Forum Icons: Forum contains no unread posts Forum contains unread posts

Topic Icons: Not Replied Replied Active Hot Sticky Unapproved Solved Private Closed