renegadesk – Aktywność

Notifications

Clear all

renegadesk

Grupa: Zarejestrowany

Dołączył: 2015/09/27

Estimable Member

	scott check the cables on both ends , If they are soldered... In forum Improvements (Archive)	9 years temu
	Mark, When printer is finisher printing it plays ghost bust... In forum Software (Archive)	9 years temu
	Nice , thanks for picture. I imagined this. Do you think th... In forum Prusa i3 kit (Archive)	9 years temu
	Peter :-O I was just looking at it for a solid minute be... In forum Prusa i3 kit (Archive)	9 years temu
	Dobre skusím, kolko má ukazovať normálna plne funkčná podlož... In forum Stavebnice Prusa i3 (Archiv)	9 years temu
	Peter Yes I thought of that expansion too. But never actual... In forum Prusa i3 kit (Archive)	9 years temu
	Pravděpodobně studený spoj (špatné spojení) na pájením spoji... In forum Stavebnice Prusa i3 (Archiv)	9 years temu
	Tie diely su asi až overkill 😀 pevné to určite ale je . ale... In forum Nejlepší výtisky & tiskové tipy	9 years temu
	Fan looks good. Its compact. But now you need that channel t... In forum Prusa i3 kit (Archive)	9 years temu
	I dont mean to dishonest someone. I just like when there is ... In forum Prusa i3 kit (Archive)	9 years temu
	Sascha Unfortunately, others see a 40W heater cartridge as ... In forum Prusa i3 kit (Archive)	9 years temu
	Asi to berie ako prvú vrstvu a tá ma nastavený pomalejšiu tl... In forum Software (Archiv)	9 years temu
	Hi, Nice that you found the problem, some people here had t... In forum Prusa i3 kit (Archive)	9 years temu
	Ano ložiska (tie guličky vovnutri) daju sa namazať ale iba t... In forum Rady k tisku (Archiv)	9 years temu
	Remen na ose X máš napnutý dostatočne ? ide rukou X lahko p... In forum Rady k tisku (Archiv)	9 years temu
	Tam to vyzera byt dobre naspájkované práveže. 🙄 Osta... In forum Stavebnice Prusa i3 (Archiv)	9 years temu
	Polovička Heatbedu nehreje In forum Stavebnice Prusa i3 (Archiv)	9 years temu
	Zkoušel si i jiné PLA? Já mám např. slonovou kost od PR (je ... In forum Rady k tisku (Archiv)	9 years temu
	True, I had the exact same problem solution is 40W cartridge... In forum Prusa i3 kit (Archive)	9 years temu
	Skus vypnúť vetrák pri PLA uplne ajtak je to velký model tak... In forum Rady k tisku (Archiv)	9 years temu

Strona 2 / 8 Wstecz Następny

Statystyki Forum

565 Fora

64.1 K Tematy

449.2 K Posty

19 Online

70.2 K Członkowie

Ostatni Post: PrusaSlicer 2.9 seems to ignore bridge direction. Najnowszy użytkownik:: shugobha Recent Posts Unread Posts Tags

Forum Icons: Forum contains no unread posts Forum contains unread posts

Ikony tematu: Not Replied Odwpowiedzi Aktywny Gorący Przyklejony Unapproved Rozwiązany Private Zamknięte