|
I'm starting to build my Mini Bear using the Blurolls kit. I... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 8 months |
|
Mini Bear with Stock Hotend? En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 8 months |
|
@karl-herbert I did it with some small diamond files. Took a... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
I bought these and also got non-pass-through fittings. I'm g... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
@cwbullet CUI make a 10mm fan with a higher throughput but i... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
It seems that Delta make the highest CFM fans in this size, ... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
Noctua are known for being quiet but not with the highest co... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
I have just noticed that in the Solex photos of the I3 nozzl... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
Are these measurements of your standard E3D V6 nozzle or you... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
OK now I'm really confused, I contacted Solex and they say t... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
@bobstro Thanks for that. The nozzles i have are 6.4mm, so a... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
@bobstro Could you measure one of your nozzles from tip to e... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
@bobstro No I didn't get the Prusa set, I got thesewhich I n... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
I've run into problems on my mini with the solex nozzles, na... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
This seems like a good idea so I've ordered the .4 and .8 no... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
Good point, I hadn't considered that and have had a quick lo... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
Actually the Dragon high flow is the same price as a Dragonf... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
Which have you used, the Copperhead or the Dragonfly? I read... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
No, I've not purchased it yet. The Dragonfly is considerably... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
|
I'm wondering if Jasii's Copperhead mount would be suitable,... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 4 years |
