Diem – Aktivität – Prusa3D Forum

Benachrichtigungen

Alles löschen

Diem

Gruppe: Registriert

Beigetreten: 2017/12/27

Illustrious Member

	It's not in there explicitly. I think you'll have to derive ... Im Forum PrusaSlicer	Vor 5 years
	PVA is water soluble ... If it has been on for a while soak ... Im Forum How do I print this? (Printing help)	Vor 5 years
	For support: Log into your Eshop account, navigate to suppor... Im Forum Assembly and first prints troubleshooting	Vor 5 years
	So my question is how do I know if the PTFE tube is at the b... Im Forum Hardware, firmware and software help	Vor 5 years
	".STL" instead of ".stl" .... Prusa thinks that the file ... Im Forum General software discussion	Vor 5 years
	If you save your project as a .3mf file, zip it, and post it... Im Forum How do I print this? (Printing help)	Vor 5 years
	If you have altered the assembly so the tube no longer fits ... Im Forum Assembly and first prints troubleshooting	Vor 5 years
	The bed is still dirty ... clean again. Did you recalibrate ... Im Forum How do I print this? (Printing help)	Vor 5 years
	It's fairly straightforward to stack parts as long as their ... Im Forum PrusaSlicer	Vor 5 years
	@john-doe-5 I guess now I have to dismantle the extruder pul... Im Forum Hardware, firmware and software help	Vor 5 years
	do you have any suggestions for what glue to use? Cheerio, Im Forum How do I print this? (Printing help)	Vor 5 years
	It's probably the side with the most fingerprints - but see ... Im Forum How do I print this? (Printing help)	Vor 5 years
	You can try annealing the print. Place it on a very flat sur... Im Forum How do I print this? (Printing help)	Vor 5 years
	OK. You are looking for DC Volts - usually shown as 'V' and... Im Forum Hardware, firmware and software help	Vor 5 years
	It'll be a couple of days before I can test-print some PETG.... Im Forum How do I print this? (Printing help)	Vor 5 years
	As which user are you running PrusaSlicer? Can that user se... Im Forum PrusaSlicer	Vor 5 years
	It slices OK but 100% fill does accentuate even minor extrus... Im Forum How do I print this? (Printing help)	Vor 5 years
	It's known that smooth PEI sheet isn't recommended for PETG.... Im Forum How do I print this? (Printing help)	Vor 5 years
	For support: Log into your Eshop account, navigate to suppor... Im Forum Assembly and first prints troubleshooting	Vor 5 years
	Perhaps it was a mistake to cut a piece off the PTFE tube (t... Im Forum Assembly and first prints troubleshooting	Vor 5 years

Seite 337 / 377 Vorherige Nächstes

Forums-Statistiken

595 Foren

70.4 K Themen

492.7 K Beiträge

13 Online

81.9 K Mitglieder

Letzter Beitrag: Stubborn PLA bridge artefact Unser neuestes Mitglied: Tocri77 Neueste Beiträge Ungelesene Beiträge Schlagwörter

Forum Icons: Das Forum enthält keine ungelesenen Beiträge Das Forum enthält ungelesene Beiträge

Themen-Icons: Unbeantwortet Beantwortet Aktiv Heiß Oben angepinnt Nicht genehmigt Gelöst Privat Geschlossen