|
Ten hour topographic print completed with the OMC (aka Stepp... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
Yes, the StepperOnline 0.9° 17HM15-0904S do work with the EI... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
STEPPERONLINE 0.9° 17HM15-0904S arrived. Wiring is a permane... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
After tracing down the 2 mm y face artifact that became more... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
Had to rearrange things on github to work on multi-color pri... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
OK I'm off the deep end chasing the 2 mm vertical artifact. ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
All good questions, but we don't really get to change wavefo... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
A pull request has been submitted. We'll see if it gets anyw... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
Now including a tower done with constant extruder linearity ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
Y-axis idler holder was out of alignment. Belt was was rubbi... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
The tower with Moons' 0.9 on extruder varies waveform power ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
Nice, felt.
Test tower for extruder consistency completed.... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
Probably not touching those limits with them already set so ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
I swapped my motors and to move a 0.9 degree on the extruder... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
Happy it is working. I tried to leave a comment on your gith... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
I love that endoscope view!
I'm just using a non-moving ca... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
Yes, it would be good if lower cost motors can work as well.... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
I have already confirmed that the Moons MS17HA2P4100 works w... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
For those unable to compile their own firmware, but wishing ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
Lower amps is cooler, but then we're into too low torque ter... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
