|
Yes, I noticed that piece on the Skelestruder. Raises the de... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Some wish to use the GPIO connection and EINSY power to avoi... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Most up to date revisions for the Bunny and Bear Geared Extr... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Glossy black PETG is my favorite and most used filament. Yes... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
If you are using a Bear extruder and want to play along, her... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
That combination should be working. I can't confirm the firm... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Yes, the combo motor plate and gearbox can't be printed with... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Which motors did you use on each axis?
Homing hit must be ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
The Skelestruder is a nifty design, but even I feel a bit in... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
I'm with Choki in thinking the gearing ratio is making much ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Is this the same as going back from 16 µsteps to 32µsteps? I... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Regarding belt vs gearing, I did build a version with printe... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
The Bunny Science Gearbox can dramatically improved extruder... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Do you really only see this only on the layer restart?
I onl... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Yes, I tried two 0.9 pancakes (with reduced micro steps) and... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 6 years |
|
Solder wicking into the wire ends and creates a very abrupt ... Dans le forum Hardware, firmware and software help |
il y a 7 years |
|
Nice, elegant solution to an eventual problem! Dans le forum Hardware, firmware and software help |
il y a 7 years |
|
If you decide on Bear build (or his axis), also grab my moto... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
The Bunny Science gearbox improves extruder uniformity compa... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
|
If you use a 1.8 degree motor, setting e-steps should be su... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 7 years |
