Notifications
Clear all
Oliver-Andre
Oliver-Andre
Groupe: Enregistré
A(ont) rejoint: 2018/04/04
Eminent Member
2
I have not tested it yet, but as far as I remember there is ...

Dans le forum User mods - OctoPrint, enclosures, nozzles, ...

il y a 3 months
First I simply just put the black cable into a dupond 1-pin ...

Dans le forum User mods - OctoPrint, enclosures, nozzles, ...

il y a 3 months
While it is possible, I personally never ever have seen a co...

Dans le forum User mods - OctoPrint, enclosures, nozzles, ...

il y a 3 months
Actually the reason theese functions are missing is Prusa Re...

Dans le forum User mods - OctoPrint, enclosures, nozzles, ...

il y a 3 months
Yes, it is the black wire. It is always ground being switche...

Dans le forum User mods - OctoPrint, enclosures, nozzles, ...

il y a 4 months
Actually I Last compiled Prusa Mini firmware about 1 1/2 yea...

Dans le forum User mods - OctoPrint, enclosures, nozzles, ...

il y a 4 months
Das Bondtech upgrade ist nicht zwingend. Durch die 3:1 Unter...

Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, …

il y a 4 months
Ich benutze seit Jahren den Bondtech upgrade extruder - aber...

Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, …

il y a 5 months
Actually I use M221 a lot. While the z-offset is for optimal...

Dans le forum General discussion, announcements and releases

il y a 5 months
In german settings it is called "Extrusionsfactor", in the d...

Dans le forum General discussion, announcements and releases

il y a 5 months
Its better known as flowrate if I understand correctly. Da h...

Dans le forum General discussion, announcements and releases

il y a 5 months
There is an option "XY slice compensation" in Print Settings...

Dans le forum General discussion, announcements and releases

il y a 5 months
As I described, just add as many skirtlines as you have virt...

Dans le forum User mods - OctoPrint, enclosures, nozzles, ...

il y a 5 months
Das sehe ich grundsätzlich genauso. Da aber Nylon ziemlich h...

Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, …

il y a 5 months
Die gelbe Leitung liefert die am Lüfter gemessene Drehzahl. ...

Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, …

il y a 5 months
SWD, DIO, CLK and RST are the typical pins for JTAG connecti...

Dans le forum User mods - OctoPrint, enclosures, nozzles, ...

il y a 5 months
J21 Pin 1 (CLK) and Pin 2 (GND) are connected with a Jumper ...

Dans le forum User mods - OctoPrint, enclosures, nozzles, ...

il y a 5 months
You can also set a z-offset in Prusa Slicer in printer setti...

Dans le forum User mods - OctoPrint, enclosures, nozzles, ...

il y a 5 months
There is an custom firmware (). It allows to set hotend fan ...

Dans le forum User mods - OctoPrint, enclosures, nozzles, ...

il y a 6 months
Thought the same. But my own programming skills are limited ...

Dans le forum User mods - OctoPrint, enclosures, nozzles, ...

il y a 6 months
Page 1 / 3
Partager :